Набор аккумуляторных инструментов SKIL F0150078AR - Инструкция по эксплуатации - Страница 9

9

• 

Store tool/charger/battery in locations where 
temperature will not exceed 40°C or drop below 0°C

• 

Do not use charger when damaged; take it to one of the 

oicially registered SKIL Service Stations for a safety 

check

• 

Do not use charger when cord or plug is damaged; cord 
or plug should be replaced immediately at one of the 

oicially registered SKIL Service Stations

• 

Do not use battery when damaged; it should be 
replaced immediately

• 

Do not disassemble charger or battery

• 

Do not attempt to recharge non-rechargeable batteries 
with the charger

EXPLANATION OF SYMBOLS ON TOOL/CHARGER/
BATTERY

③

Warning

! Read the instruction manual

④

   Do not expose tool/charger/battery to rain

⑤

   Wear protective glasses and hearing protection

⑥

Pay attention to the risk of injury caused by lying 

debris

 (keep bystanders a safe distance away from 

work area)

⑦

   Only use the charger indoors

⑧

   Double insulation (no earth wire required)

⑨

    Batteries may explode when disposed of in ire, so do 

not burn battery for any reason

⑩

    Store tool/charger/battery in locations where 

temperature will not exceed 50°C

⑪

    Do not dispose of the charger together with household 

waste material

⑫

    Do not dispose of the battery together with household 

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• 

If for any reason the old plug is cut of the cord of the 

charger, it must be disposed of safely and not left 
unattended

• 

Do not connect the blue (= neutral) or brown (= live) wire 
in the cord of the charger to the earth terminal of the 
plug

USE

• 

Always remove battery from tool before making any 
adjustment or changing any accessory, in order to 
reduce the risk of starting the tool accidentally

• 

Assembly instructions 

⑬

-

  the sequence of the numbers appearing in the drawing 

corresponds with the sequence of the steps to be 
followed for assembling the tool

-

  mount cutting guard A as illustrated with round head 

screw supplied

!

irmly tighten all screws

!

  never use the tool without cutting guard A

• 

Adjusting guide handle 

⑭

-

  loosen/tighten handle B 

②

 by turning it 

counter-clockwise/clockwise

• 

Height adjustment 

⑮

For adjusting the tool height so that your front arm is 
straight when trimming

-

  loosen locking sleeve C by turning it clockwise

-

  extend tube D to the desired height

-

  tighten locking sleeve C by turning it counter-clockwise

• 

Charging battery 

⑯

-

  battery of new tools is not fully charged

-

  connect charger E to power source as illustrated 

⑯

a

-

  green light F will turn on indicating that the charger is 

ready for operation 

⑯

a

-

  insert battery G into charger as illustrated 

⑯

b

-

  green light F will blink indicating that the battery is 

being charged 

⑯

b

-

  after approximately 1 hour the battery is fully charged 

and green light F stays on after blinking 

⑯

c

IMPORTANT:

-

  if green light F does not blink after inserting a battery, 

this may mean:

      1)  that the battery is too cold or too hot (charger only 

charges batteries when its temperature is between 
0°C and 45°C)

      2) that the battery should be replaced

-

  the lithium-ion battery can be charged at any time 

(interrupting the charging procedure does not damage 
the battery)

-

  the lithium-ion battery does not have to be empty 

before charging (no "memory-efect" as with nickel-

cadmium batteries)

-

  while charging, the charger and the battery may 

become warm to touch; this is normal and does not 
indicate a problem

-

  ensure that the outside surface of the battery is clean 

and dry before inserting into charger

-

  do not remove battery from tool while it is running

-

  a signiicantly reduced working period after charging 

indicates that the battery is worn out and should be 
replaced

• 

Battery protection 

Switches of the tool automatically when

    1) the load is too high
    2)  the battery temperature is not within the allowable 

operating temperature range of -10 to +50°C

    3)  the lithium-ion battery is nearly empty (to protect 

against deep discharge)

!

do not continue to press the on/of switch after 

the tool is switched of automatically; battery may 

be damaged

• 

On/of 

⑰

-

  switch on/of the tool by pulling/releasing trigger H

!

after switching of the tool the blade continues to 

rotate for a few seconds

-

  allow the cutting blade to stop rotating before 

switching on again

!

do not rapidly switch on and of

• 

Trimming

!

  ensure that the cutting area is free of stones, 

debris and other foreign objects

!

  start trimming only when tool runs at full speed

-

  cut long grass in layers (always start from the top)

-

  only trim with the tip of the cutting blade

-

  do not cut damp or wet grass

-

  prevent the cut grass from clogging the blade (do not 

make heavy cuts)

-

  do not overload the tool

-

  carefully cut around trees and bushes, so that they do 

not come into contact with the cutting blade

-

  use lower guard J 

⑱

 to protect vulnerable lowers

-

  keep the tool away from solid objects in order to 

protect the cutting blade against excessive wear

-

  be aware of the kickback forces that occur when solid 

objects are touched