Набор аккумуляторных инструментов SKIL F0150078AR - Инструкция по эксплуатации - Страница 10

10

• 

Holding and guiding the tool 

⑲

-

  for cutting long grass slowly swing the tool from right to 

left and vice versa

-

  for cutting shorter grass tilt the tool as illustrated

-

  turn the tool 180° for trimming edges

-

  hold tool irmly with both hands, so you will have full 

control of the tool at all times

-

  maintain a stable working position

-

  always hold the tool well away from your body

• 

Replacing cutting blade 

⑳

!

  remove battery from tool

-

  simply remove/mount old/new cutting blade as 

illustrated

-

  after replacing the cutting blade test-run the tool for at 

least one minute without load to ensure that the tool is 
operating properly

-

  extend the service life of the cutting blade twice by 

removing it, turning it 180°, and mounting it again

• 

Blade storage compartment 

㉑

MAINTENANCE / SERVICE

• 

This tool is not intended for professional use

• 

Opening the housing shell can damage or destroy 
the tool

• 

Keep tool, charger and cutting blades clean

!

  unplug charger from power source before 

cleaning

!

  always remove the battery before cleaning

-

  clean cutting blade L 

②

 and cutting guard A 

②

 after 

each use

-

  clean the tool with a damp cloth (do not use cleaning 

agents or solvents)

-

  clean ventilation slots M 

②

 regularly with a brush or 

compressed air

• 

Regularly check the condition of the cutting head and 
the tightness of nuts, bolts and screws

• 

Regularly check for worn or damaged components and 
have them repaired/replaced when necessary

• 

Storage 

-

  store the tool 

indoors

 in a dry and locked-up place, 

out of reach of children

-

  securely mount storage rail N on the wall with 4 screws 

(

not supplied

) and horizontally leveled

• 

If the tool/charger should fail despite the care taken in 

manufacturing and testing procedures, repair should 

be carried out by an after-sales service centre for SKIL 

power tools

-

  send the tool or charger 

undismantled

 together with 

proof of purchase to your dealer or the nearest SKIL 

service station (addresses as well as the service 

diagram of the tool are listed on www.skil.com)

-

  in case of a defective charger send 

both charger and 

battery

 to your dealer or the SKIL service station

TROUBLESHOOTING

• 

The following listing shows problem symptoms, possible 
causes and corrective actions (if these do not identify 
and correct the problem, contact your dealer or service 
station)

!

switch of the tool and remove the battery before 

investigating the problem

★ 

Tool operates intermittently

-

  internal wiring defective -> contact dealer/service 

station

-

  on/of switch defective -> contact dealer/service 

station

★ 

Tool vibrates abnormally

-

  grass too high -> cut in stages

★ 

Tool does not cut

-

  cutting blade broken of -> replace cutting blade

ENVIRONMENT

• 

Do not dispose of electric tools, batteries, 
accessories and packaging together with 
household waste material

 (only for EU countries)

-

  in observance of European Directive 2012/19/EC 

on waste of electric and electronic equipment and 
its implementation in accordance with national law, 
electric tools that have reached the end of their life 
must be collected separately and returned to an 
environmentally compatible recycling facility

-

 symbol 

⑪

 will remind you of this when the need for 

disposing occurs

!

  remove the battery before disposal of the tool

• 

The battery must be kept separate from the natural 
environment and should not be disposed of as normal 
domestic waste (symbol 

⑫

 will remind you of this when 

the need for disposing occurs)

!

  prior to disposal protect battery terminals with 

heavy tape to prevent short-circuit

-

  dispose of the battery at an oicial collection point for 

batteries

!

batteries may explode when disposed of in ire, 

so do not burn battery for any reason

 DECLARATION OF CONFORMITY 

• 

We declare under our sole responsibility that this 
product is in conformity with the following standards 

or standardized documents: EN 60335, EN 61000, 

EN 55014 in accordance with the provisions of the 
directives 2006/95/EC, 2004/108/EC, 2006/42/EC, 
2000/14/EC, 2011/65/EU

•  Technical ile at

: SKIL Europe BV (PT-SEU/ENG1), 

4825 BD Breda, NL

11.04.2014

SKIL Europe BV, 4825 BD Breda, NL

Marijn van der Hoofden
Operations & Engineering

Olaf Dijkgraaf
Approvals Manager

13

NOISE/VIBRATION 

• 

Measured in accordance with EN 60335 the sound 
pressure level of this tool is <70 dB(A) (standard 

deviation: 3 dB) and the vibration 1 m/s² (hand-arm 

method; uncertainty K = 1.5 m/s²)

• 

Measured in accordance with 2000/14/EC the 
guaranteed sound power level LWA is lower than 86 
dB(A) (conformity assessment procedure according to 

Annex VI)

Notiied body : INTERTEK

Notiied body identiication number : 0359

• 

The vibration emission level has been measured in 
accordance with a standardised test given in EN 60335; 
it may be used to compare one tool with another and as