Набор аккумуляторных инструментов SKIL F0150078AR - Инструкция по эксплуатации - Страница 160

8

MAINTENANCE / SERVICE

• 

This tool is not intended for professional use

• 

Keep tool, charger and cutting blades clean

!

  unplug charger from power source before 

cleaning

!

  always remove the battery before cleaning

-

  clean the tool with a damp cloth (do not use cleaning 

agents or solvents)

-

  clean ventilation slots K 

②

 regularly with a brush or 

compressed air

-

  after use, always carefully clean and lightly lubricate 

the cutting blades

!

  wear gloves when handling or cleaning the 

cutting blades

• 

Regularly check the condition of the cutting blades and 
the tightness of the blade bolts

• 

Regularly check for worn or damaged components and 

have them repaired/replaced when necessary

• 

Sharpening the cutting blades

!

  remove battery from tool

-

  sharpen the cutting blades with a small and smooth 

ile, in case a solid object damaged them

-

  we advise you, however, to have the blades sharpened 

by a specialist

-

  lubricate the cutting blades after sharpening

• 

Storage 

⑰

-

  store the tool 

indoors

 in a dry and locked-up place, 

out of reach of children

-

  securely mount storage rail L on the wall with 4 screws 

(

not supplied

) and horizontally leveled

-

  use blade cover M when storing the tool

-

  before storing the tool, wipe of the cutting blades with 

an oil-soaked rag to prevent corrosion

• 

If the tool/charger should fail despite the care taken in 

manufacturing and testing procedures, repair should 
be carried out by an after-sales service centre for SKIL 
power tools

-

  send the tool or charger 

undismantled

 together with 

proof of purchase to your dealer or the nearest SKIL 
service station (addresses as well as the service 

diagram of the tool are listed on www.skil.com)

-

  in case of a defective charger send 

both charger and 

battery

 to your dealer or the SKIL service station

TROUBLESHOOTING

• 

The following listing shows problem symptoms, possible 
causes and corrective actions (if these do not identify 
and correct the problem, contact your dealer or service 
station)

!

switch of the tool and remove the battery before 

investigating the problem

★ 

Tool operates intermittently

-

  internal wiring defective -> contact dealer/service 

station

-

  on/of switch defective -> contact dealer/service 

station

★ 

Motor runs but blades remain stationary

-

  internal fault -> contact dealer/service station

★ 

Cutting blades hot

-

  cutting blades blunt -> have blades sharpened

-

  cutting blades have dents -> have blades inspected

-

  too much friction due to lack of lubricant -> lubricate 

blades

ENVIRONMENT

• 

Do not dispose of electric tools, batteries, 
accessories and packaging together with 
household waste material

 (only for EU countries)

-

  in observance of European Directive 2012/19/EC 

on waste of electric and electronic equipment and 
its implementation in accordance with national law, 
electric tools that have reached the end of their life 
must be collected separately and returned to an 
environmentally compatible recycling facility

-

 symbol 

⑩

 will remind you of this when the need for 

disposing occurs

!

  remove the battery before disposal of the tool

• 

The battery must be kept separate from the natural 
environment and should not be disposed of as normal 
domestic waste (symbol 

⑪

 will remind you of this when 

the need for disposing occurs)

!

  prior to disposal protect battery terminals with 

heavy tape to prevent short-circuit

-

  dispose of the battery at an oicial collection point for 

batteries

!

batteries may explode when disposed of in ire, 

so do not burn battery for any reason

 DECLARATION OF CONFORMITY 

• 

We declare under our sole responsibility that this 
product is in conformity with the following standards or 

standardized documents: EN 60335, EN 60745, EN 

61000, EN 55014 in accordance with the provisions of 

the directives 2006/95/EC, 2004/108/EC, 2006/42/EC, 

2000/14/EC, 2011/65/EU

•  Technical ile at

: SKIL Europe BV (PT-SEU/ENG1), 

4825 BD Breda, NL

11.04.2014

SKIL Europe BV, 4825 BD Breda, NL

Marijn van der Hoofden
Operations & Engineering

Olaf Dijkgraaf
Approvals Manager

13

NOISE/VIBRATION 

• 

Measured in accordance with EN 60745 the sound 
pressure level of this tool is <70 dB(A) (standard 

deviation: 3 dB) and the vibration 1.3 m/s² (hand-arm 

method; uncertainty K = 1.5 m/s²)

• 

Measured in accordance with 2000/14/EC the 

guaranteed sound power level LWA is lower than 91 

dB(A) (conformity assessment procedure according to 
Annex V)

• 

The vibration emission level has been measured in 

accordance with a standardised test given in EN 60745; 

it may be used to compare one tool with another and as 
a preliminary assessment of exposure to vibration when 
using the tool for the applications mentioned

-

  using the tool for diferent applications, or with diferent 

or poorly maintained accessories, may signiicantly 

increase

 the exposure level

-

  the times when the tool is switched of or when it is 

running but not actually doing the job, may signiicantly 

reduce

 the exposure level