Bosch GSR 18 V-EC TE 0.601.9С8.001 - Инструкция по эксплуатации - Страница 14

 English | 

13

Bosch Power Tools

1 609 92A 0WV | (9.10.14)

Noise/Vibration Information

Sound emission values determined according to 
EN 60745-2-1.

Typically the A-weighted sound pressure level of the product 
is 75 dB(A). Uncertainty K = 3 dB.
The noise level when working can exceed 80 dB(A).

Wear hearing protection!

Vibration total values a

h

 (triax vector sum) and uncertainty K 

determined according to EN 60745:
Screwdriving without impact: a

h

< 2,5 m/s

2

, K = 3 m/s

2

.

The vibration level given in this information sheet has been 
measured in accordance with a standardised test given in 
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different 
applications, with different accessories or insertion tools or is 
poorly maintained, the vibration emission may differ. This 
may significantly increase the exposure level over the total 
working period.
An estimation of the level of exposure to vibration should also 
take into account the times when the tool is switched off or 
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working 
period.
Identify additional safety measures to protect the operator 
from the effects of vibration such as: maintain the tool and the 
accessories, keep the hands warm, organisation of work pat-
terns.

Declaration of Conformity

We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with all rele-
vant provisions of the directives 2009/125/EC (Regulation 
1194/2012), 2011/65/EU, 2014/30/EU, 2006/42/EC in-
cluding their amendments and complies with the following 
standards: EN 60745-1, EN 60745-2-1, EN 60745-2-2.

Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
70764 Leinfelden-Echterdingen, GERMANY

Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
09.10.2014

Assembly

Battery Charging



Use only the battery chargers listed on the accessories 
page. 

Only these battery chargers are matched to the lith-

ium-ion battery of your power tool.

Note: 

The battery supplied is partially charged. To ensure full 

capacity of the battery, completely charge the battery in the 
battery charger before using your power tool for the first time.

The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure 
does not damage the battery.

The lithium-ion battery is protected against deep discharging 
by the “Electronic Cell Protection (ECP)”. When the battery is 
empty, the machine is switched off by means of a protective 
circuit: The inserted tool no longer rotates.



Do not continue to press the On/Off switch after the 
machine has been automatically switched off. 

The bat-

tery can be damaged.

Observe the notes for disposal.

Removing the battery

The battery 

9

 is equipped with two locking levels that should 

prevent the battery from falling out when pushing the battery 
unlocking button 

10

 unintentionally. As long as the battery is 

inserted in the power tool, it is held in position by means of a 
spring.

To remove the battery 

9

, press the unlocking button 

10

 and 

pull out the battery toward the front. 

Do not exert any force.

Changing the Tool (see figure A)



Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport 
and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.

Permitted ambient 
temperature

– during charging
– during operation

**

 and 

during storage

°C
°C

0... +45

-20... +50

Recommended batteries

GBA 18V..

GBA 18V... W

Recommended chargers

AL 18..

GAL 3680

Recommended chargers for 
wireless charging batteries

GAL 18... W

Cordless Screwdriver

GSR  18 V-EC TE

*Depending on the battery pack being used

** Limited performance at temperatures < 0 ° C

Henk Becker
Executive Vice President
Engineering

Helmut Heinzelmann
Head of Product Certification
PT/ETM9

OBJ_DOKU-35033-002.fm  Page 13  Thursday, October 9, 2014  1:01 PM