Bosch 0.601.B19.200 - Инструкция по эксплуатации - Страница 36

36

 | English

1 609 92A 3UK | (07.08.2018)

Bosch Power Tools

– Pull the stop 

(44)

 all the way forward.

– Turn the right-hand stop 

(29)

 until the standard 45° bevel

angle engages at the arrow mark.

– Loosen the clamping lever 

(41)

.

– Swivel the tool arm by the handle 

(9)

 to the right until the

stop screw 

(60)

 rests on the stop 

(29)

.

Checking (see figure V1)

– Set an angle gauge to 135° and place it on the saw table

(16)

.

The leg of the angle gauge must be flush with the saw blade

(12)

 along its entire length.

Setting (see figure V2)

– Loosen the lock nut of the stop screw 

(59)

 using a con-

ventional ring spanner or open-end spanner (10 mm).

– Twist the stop screw as far in or out as needed until the

leg of the angle gauge is flush with the saw blade over the
entire length.

– Retighten the clamping lever 

(41)

.

– Then retighten the lock nut of the stop screw 

(59)

.

If the angle indicators 

(42)

 and 

(31)

 are not in line with the

45° marks on the scale 

(30)

 following adjustment, first

check the 0° setting for the bevel angle and the angle indicat-
ors once more. Then repeat the adjustment of the 45° bevel
angle.

Aligning the scale for mitre angles

– Bring the power tool into the work position.
– Turn the saw table 

(16)

 to the 0° detent 

(25)

. The lever

(22)

 must be felt to engage in the detent.

Checking (see figure W1)

– Set an angle gauge to 90° and position it between the

fence 

(14)

 and the saw blade 

(12)

 on the saw table 

(16)

.

The leg of the angle gauge must be flush with the saw blade

(12)

 along its entire length.

Setting (see figure W2)

– Loosen all four set screws 

(61)

 with a cross-headed

screwdriver and turn the saw table 

(16)

 together with the

scale 

(18)

 until the leg of the angle gauge is flush with the

saw blade over the entire length.

– Retighten the screws again.
If the angle indicator 

(24)

 is not aligned with the 0° mark on

the scale 

(18)

 following adjustment, loosen the screw 

(62)

using a cross-headed screwdriver and align the angle indic-
ator along the 0° mark.

Transport (see figure X)

Before transporting the power tool, the following steps must
be carried out:
– Loosen the locking screw 

(33)

 if it is tightened. Pull the

tool arm fully forwards and retighten the locking screw.

– Make sure that the depth stop 

(32)

 is pressed all the way

in and that the adjusting screw 

(4)

 fits through the recess

without touching the depth stop when moving the tool
arm.

– Bring the power tool into the transport position.

– Remove all accessories that cannot be securely fitted to

the power tool. If possible, transport unused saw blades
in an enclosed container.

– Wind up the mains cable and tie it together with the hook-

and-loop strap 

(63)

.

– Carry the power tool by the transport handle 

(3)

 or hold it

by the recessed handles 

(27)

 on the sides of the saw

table.

u

Only use the transport devices to transport the power
tool and never the protective devices.

Maintenance and servicing

Maintenance and cleaning

u

Pull the plug out of the socket before carrying out any
work on the power tool.

u

To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.

In order to avoid safety hazards, if the power supply cord
needs to be replaced, this must be done by Bosch or by a
customer service centre that is authorised to repair Bosch
power tools.
The retracting blade guard must always be able to move
freely and retract automatically. It is therefore important to
keep the area around the retracting blade guard clean at all
times.
Always remove dust and chips after working by blowing out
with compressed air or using a brush.
Clean the guide roller 

(6)

 regularly.

To clean the laser unit, turn the laser cover 

(64)

 outwards

and remove the dust with a paintbrush (see figure 

Y

).

Accessories

Article number

Screw clamp

1 609 B04 224

Insert plates

1 609 B03 717

Dust bag

1 609 B05 010

Length stop

1 609 B02 365

Locking screw for length stop

1 609 B00 263

Saw blades for wood and fibreboard, panels and strips

216 x 30 mm saw blade, 48 teeth

2 608 640 641

Saw blades for plastic and non-ferrous metals

216 x 30 mm saw blade, 80 teeth

2 608 640 447

216 x 25.4 mm saw blade, 80 teeth

2 608 642 993

Saw blades for all types of laminate flooring

216 x 30 mm saw blade, 60 teeth

2 608 642 133

216 x 25.4 mm saw blade, 60 teeth

2 608 642 995

After-sales service and advice on using products

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on