Bosch 0.601.B19.200 - Инструкция по эксплуатации - Страница 32

32

 | English

1 609 92A 3UK | (07.08.2018)

Bosch Power Tools

– Slowly guide the tool arm downwards using the handle

(9)

.

– Guide the tool arm downwards until you can press the

transport safety lock 

(37)

 all the way in.

Preparing for operation

Extending the saw table (see figure E)

The free end of long workpieces must have something
placed underneath it or be supported.

The saw table can be extended left and right using the saw
table extensions 

(13)

.

– Pull the clamping lever 

(17)

 upwards.

– Pull out the saw table extension 

(13)

 to the required

length.

– To lock the saw table extension, push the clamping lever

(17)

 back down.

Moving the fence

(see figure 

F

)

When sawing mitre/bevel angles, you must pull the left-hand or right-hand adjustable fence 

(15)

 (depending on the cutting dir-

ection) outwards, or remove it completely.

Bevel angle

Mitre angle

0°–47°

(left)

≤ 44° 

(right/left)

–

Loosen

 the locking screw 

(51)

.

– Pull the left-hand adjustable fence

(15)

 all the way out.

0°–47° 

(left)

≥ 45° 

(right/left)

–

Loosen

 the locking screw 

(51)

.

– Pull the left-hand adjustable fence

(15)

 all the way out.

– Lift the adjustable fence upwards and

out of the way.

–

Remove

 the locking screw 

(51)

.

0°–47° 

(right)

≤ 44° 

(right/left)

–

Loosen

 the locking screw 

(51)

.

– Pull the right-hand adjustable fence

(15)

 all the way out.

– Lift the adjustable fence upwards and

out of the way.

0°–47° 

(right)

≥ 45° 

(right/left)

–

Loosen

 the locking screw 

(51)

.

– Pull the right-hand adjustable fence

(15)

 all the way out.

– Lift the adjustable fence upwards and

out of the way.

Clamping the workpiece (see figure G)

– Press the workpiece firmly against the fence 

(14)

.

– Insert the supplied screw clamp 

(28)

 into one of the holes

(35)

 intended for this purpose.

– Adjust the threaded rod 

(52)

 of the screw clamp to the

workpiece height.

– Tighten the threaded rod 

(52)

 to fix the workpiece in

place.

Adjusting mitre angles

To ensure precise cuts, the basic settings of the power tool
must be checked and adjusted as necessary after intensive
use (see "Checking and adjusting the basic settings",
page 35).

Setting standard mitre angles (see figure H)

For quick and precise setting of commonly used mitre
angles, detents 

(25)

 are provided on the saw table:

Leftward

Rightward

0°

45°; 31.6°; 22.5°; 15°

15°; 22.5°; 31.6°; 45°; 60°

– Loosen the locking knob 

(21)

 if it is tightened.

– Pull the lever 

(22)

 and rotate the saw table 

(16)

 left or

right to the required detent.

– Release the lever again. The lever must be felt to engage

in the detent.

– Retighten the locking knob 

(21)

.

Setting any mitre angle (see figure I)

The mitre angle can be set between 52° (left side) and 60°
(right side).
– Loosen the locking knob 

(21)

 if it is tightened.

– Pull the lever 

(22)

 and at the same time press the locking

clamp 

(20)

 until this clicks into the slot provided for it.

This means the saw table can now move freely.