Bosch GTS 10 XC - Инструкция по эксплуатации - Страница 30

30

 | English 

1 619 929 K16 | (29.8.11)

Bosch Power Tools

Safety Warnings for Table Saws

f

Never stand on the power tool. 

Serious injuries can occur 

when the power tool tips over or when inadvertently com-

ing into contact with the saw blade.

f

Take care that the blade guard operates properly and 

can move freely. 

Always adjust the blade guard in such a 

manner that it faces loosely against the workpiece when 

sawing. Never clamp the blade guard when it is open.

f

Never reach behind the saw blade in order to hold the 

workpiece, remove saw dust/wood chips or for any oth-

er reason. 

The clearance of your hand to the rotating saw 

blade is too small.

f

Guide the workpiece against the saw blade only when 

the machine is switched on. 

Otherwise there is damage 

of kickback, when the saw blade becomes wedged in the 

workpiece.

f

Keep handles dry, clean, and free from oil and grease. 

Greasy, oily handles are slippery causing loss of control.

f

Operate the power tool only when the work area to the 

workpiece is clear of any adjusting tools, wood chips, 

etc. 

Small pieces of wood or other objects that come in 

contact with the rotating saw blade can strike the operator 

with high speed.

f

Only saw one workpiece at a time. 

Workpieces placed on 

top or aside of each other can cause the saw blade to jam 

or the workpieces to move against each other while saw-

ing.

f

Always use the parallel guide or the angle guide. 

 This 

improves the cutting accuracy and reduces the possibility 

of saw blade binding.

f

Use the machine for grooving or rebating only with an 

appropriately suitable protective device (e. g. a tunnel 

blade guard).

f

Do not use the machine for cutting slots (stopped 

grooves).

f

Use the machine only for cutting the materials listed 

under Intended Use. 

Otherwise, the machine can be sub-

ject to overload.

f

If the saw blade should become jammed, switch the ma-

chine off and hold the workpiece until the saw blade 

comes to a complete stop. To prevent kickback, the 

workpiece may not be moved until after the machine 

has come to a complete stop. 

Correct the cause for the 

jamming of the saw blade before restarting the machine.

f

Do not use dull, cracked, bent or damaged saw blades. 

Unsharpened or improperly set saw blades produce nar-

row kerf causing excessive friction, blade binding and kick-

back.

f

Always use saw blades with correct size and shape (dia-

mond versus round) of arbor holes. 

Saw blades that do 

not match the mounting hardware of the saw will run ec-

centrically, causing loss of control.

f

Do not use high speed steel (HSS) saw blades. 

Such saw 

blades can easily break.

f

Do not touch the saw blade after working before it has 

cooled. 

The saw blade becomes very hot while working.

f

Never operate the machine without the insert plate. 

Replace a defective insert plate. 

Without flawless insert 

plates, injuries are possible from the saw blade.

f

Check the cable regularly and have a damaged cable re-

paired only through an authorised customer service 

agent for Bosch power tools. Replace damaged exten-

sion cables. 

This will ensure that the safety of the power 

tool is maintained.

f

Store the machine in a safe manner when not being 

used. The storage location must be dry and lockable. 

This prevents the machine from storage damage, and from 

being operated by untrained persons.

f

Never leave the machine before it has come to a com-

plete stop. 

Cutting tools that are still running can cause in-

juries.

f

Never use the machine with a damaged cable. Do not 

touch the damaged cable and pull the mains plug when 

the cable is damaged while working. 

Damaged cables in-

crease the risk of an electric shock.

Products sold in GB only

: Your product is fitted with an 

BS 1363/A approved electric plug with internal fuse (ASTA 

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be 

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should 

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible 

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols can be important for the operation of 

your power tool. Please memorise the symbols and their 

meanings. The correct interpretation of the symbols helps 

you operate the power tool better and more secure.

Symbols and their meaning

Keep hands away from the cutting area 

while the machine is running. 

Danger of 

injury when coming in contact with the saw 

blade.

Wear a dust respirator.

Wear ear protectors. 

Exposure to noise 

can cause hearing loss.

OBJ_BUCH-1375-002.book  Page 30  Monday, August 29, 2011  5:05 PM