JVC SR-VS30E - Инструкция по эксплуатации - Страница 57

57

A

Make connections.

Connect the player’s VIDEO OUT or S-VIDEO OUT and 
AUDIO OUT connectors to your recorder’s VIDEO or 
S-VIDEO and AUDIO input connectors on the front 
panel.

B

Select the recording deck.

Press 

VHS

 or 

DV

.

●

When using the DV deck as the recording deck, press 

 so 

that the video and audio signals from the VIDEO/S-VIDEO and 
AUDIO L + R input connectors can be recorded. The dubbing 
direction indicator (

VHS) lights.

C

Load a cassette.

For the VHS deck

Insert a VHS (or S-VHS) cassette with the record safety 
tab intact, or cover the hole using adhesive tape.

For the DV deck

Insert a Mini DV cassette with the erase protection switch 
set to “REC”.

D

Set the recorder’s input mode.

Press 

AUX

 (

number key

 “

0

”) and/or 

PR

 to select “F-1”.

●

When using the VHS deck as the recording deck, set “VHS F-1 
INPUT” to “VIDEO” for the AUDIO/VIDEO input connectors, 
or “S-VIDEO” for the AUDIO/S-VIDEO input connectors, 
depending on the connectors being used. (

墌

pg. 53) 

E

Prepare the recording cassette.

For the VHS deck

Load the recording cassette into the VHS deck, and play 
it back to determine the edit-out point (the end of the 
segment to be replaced) using the 

JOG

 dial, or pressing 

w

e

 and 

9

.

Then press 

0000

 to reset the counter.

For the DV deck

Load the recording cassette into the DV deck.

F

Locate the start point.

Press 

4

 to start playback of the tape in your recorder, and 

press 

9

 when you reach the point where you want to start 

dubbing.

G

Engage the Insert Editing mode.

Press 

INSERT

.

●

Your recorder enters the Insert Pause mode. (“

o

”, “

u

” and 

“

i

” light up on the front display panel.)

●

The TV screen changes from the still picture to the input 
source you are going to record.

H

Start Editing.

Load the source cassette and play back the segment that 
is to be inserted. When you reach the start of the section 
of the source tape that you wish to insert, press 

4

 to start 

the tape in your recorder; Insert Editing begins at this 
point.

●

“

o

” and “

u

” are displayed on the front display panel.

I

End Insert Editing.

For the VHS deck

At counter “0:00:00”, Insert Editing will stop 
automatically while the tape continues running in the 
Play mode. If you wish to stop Insert Editing before the 
specified edit-out point, press 

0000

.

For the DV deck

Press 

8

 to stop recording on the DV deck.

AV Insert Editing (VHS deck only)

If you want to replace the picture, Hi-Fi audio soundtrack 
and normal audio soundtrack all at the same time ...
... In step 

7

, after you press 

INSERT

, press 

A.DUB

 also.

(

“

o

” and “

u

” blink and “

i

” lights up on the front display 

panel.)

NOTES:

●

Once the Insert Editing starts, you can not use the other deck.

●

All necessary cables can be obtained from your dealer.

●

Insert Editing cannot be performed on a VHS (or S-VHS) 
cassette that has had its record safety tab removed, or on a 
Mini DV cassette that has had its erase protection switch set to 
“SAVE”.

●

When Insert Editing is performed on a tape that has been 
recorded on another video recorder, the inserted portion may 
appear distorted.

●

In Insert Editing, the recording speed (SP/LP) is determined by 
the previous recording to be replaced. If the previous 
recording’s speed changes within a single edit, the inserted 
picture will be distorted at the switching point. (VHS deck 
only)

●

A small portion of the recording which precedes an insert edit 
may become erased.

●

Insert Editing is also possible using the rear panel AV1 (L-1) IN/
OUT or AV2 (L-2) IN/DECODER connector. When using these 
21-pin SCART connectors, be sure to select the correct input 
mode (“L-1” or “L-2”) in step 

4

.

●

Insert Editing is not possible using the DV IN/OUT connector.

●

Insert Editing is not possible on a blank portion of the tape.