JVC SR-VS30E - Инструкция по эксплуатации - Страница 37

37

G

Check the programme data.

The front display panel shows the programme start time. 
Pressing 

"

 changes the display to the programme stop 

time, then the date and channel position.

H

Set the tape speed.

Press 

SP/LP

 (

p

).

I

Set the PDC mode.

Press 

PDC

 to select “ON” or “OFF”.

●

If “VPS/PDC ON” is displayed on the TV screen or “VPS/PDC” 
is lit on the front display panel, PDC is set to ON.

●

If “VPS/PDC OFF” is displayed on the TV screen or “VPS/PDC” 
is not lit on the front display panel, PDC is set to OFF.

墌

“PDC Recording” on page 39.

●

VPS (Video Programme System) recording is not currently 
available in the U.K. and not possible with this recorder.

J

Return to the normal screen.

Press 

PROG

 or 

OK

. “PROGRAM COMPLETED” appears 

on the TV screen for about 5 seconds, then the normal 
screen appears. If “PROGRAM OVERLAPPED” appears 
on the TV screen and “Err” on the front display panel, see 
page 43.

●

Repeat steps 

3

 – 

10

 for each additional programme.

K

Engage the recorder’s timer mode.

Press 

#

 (

TIMER

). The recorder turns off automatically and 

“

#

” appears on the front display panel.

●

To disengage the timer mode, press 

#

 (

TIMER

) again.

NOTES:

●

To Change The Stop Time . . .
. . . press 

STOP

+/–

 in step 

7

. You can compensate for 

anticipated programme schedule delays.

●

To Timer-Record Weekly Or Daily Serials . . .
. . . in  step 

7

, press 

WEEKLY

 (

number key

 “

9

”) for weekly 

serials or 

DAILY

 (

number key

 “

8

”) for daily serials (Monday — 

Friday). Either “WEEKLY” or “DAILY” appears on the TV 
screen. Pressing the button again makes the corresponding 
indication disappear.

●

You can programme each deck to timer-record as many as 6 
programmes. If you try to programme the recorder to record a 
seventh, “PROGRAM FULL” appears on the TV screen and 
“FULL” appears on the front display panel. To record the extra 
programme, you must first cancel any unnecessary 
programmes (

墌

pg. 42).

●

It is not possible to timer-record a TV programme with a 
PlusCode number which starts with “0”.

●

It is not possible to timer-record a satellite broadcast received 
on the channel position “0” by the satellite receiver.

●

It is not possible to timer-record the same programme on both 
the VHS deck and the DV deck simultaneously.

●

During timer recording, it is not possible to change the 
recording deck (VHS or DV).

●

If the times that are programmed for recording on the DV deck 
and on the VHS deck overlap, the earlier start time takes 
precedence. If the start times are the same, the VHS deck 
takes precedence.

The PlusCode number you 
entered and the matching 
timer-recording information 
are displayed on the TV 
screen. Check they are 
correct.

IMPORTANT

Make sure the channel position number you wish to record is 
displayed; if not, see “VIDEO Plus+

®

 System Setup” on 

page 82 and set the Guide Program number correctly.

Satellite Receiver Users

To timer-record a satellite broadcast using the VIDEO Plus+ 
system:

A

Perform “Satellite Receiver Control Setting” on page 17.

B

Perform steps 

1

 – 

11

. In step 

7

, the front display panel 

shows “L2” for the channel position. In step 

9

, you cannot 

set “PDC” to “ON”.

C

Leave the satellite receiver’s power on.

INFORMATION

Instead of the steps 

4

–

6

, you can enter the PlusCode 

number using the on-screen menu.

A

Press 

PROG

 to access the PlusCode screen.

B

Press the 

number keys

 to 

enter the PlusCode number 
of a programme you wish to 
record.

●

If you make a mistake, 
press 

&

 and input the 

correct number.

C

Press 

OK

, then go to step

7

in the left column.

●

If the number you entered 
is invalid, “ERROR” appears on the TV screen and “Err” 
appears on the front display panel. Input a valid 
PlusCode number.

●

If the “GUIDE PROG SET” screen appears, see 
“ATTENTION” below.

ATTENTION

Guide Program Number Set

“GUIDE PROG SET” appears after performing step 

C

 above 

if the Guide Program number for the PlusCode number you 
entered has not been set.
If you want to set the Guide Program number for the satellite 
broadcast station, press the 

number key

 “

0

” to change “TV 

PROG” to “SAT”. Press 

rt

 to input the channel position 

number on which your recorder or satellite receiver receives 
that station, then press 

OK

 or 

e

 to set the Guide Program 

number. The VIDEO Plus+ Program screen appears.

(Example) 
To timer-record a BBC2 
programme with the VIDEO 
Plus+ system. 

* If your recorder receives BBC2 

on the channel position 2, press 

OK

 or 

e

 after entering “2”.