Yamaha RX-V365 - Инструкция по эксплуатации - Страница 21

17

 En

Optimizing the speaker setting for your listening room (YPAO)

English

INTR

ODUCTION

AD

DITIONAL 

INFORMA

T

ION

APPENDIX

PRE

P

ARA

T

ION

BA

S

IC

OPERA

T

ION

AD

V

ANCED

OPERA

T

ION

Notes

•

During the automatic setup procedure, do not perform any 
operation on this unit.

•

We recommend that you get out of the room while this unit is in the 
auto setup procedure. It takes approximately 3 minutes for this unit 
to complete the auto setup procedure.

6

When all measurements are completed 
successfully, “FINISH” appears on the front 
panel display.

The result of the automatic setup for each speaker 
appears in order on the front panel display.

y

•

To display the result of the automatic setup again, press 

l

k

 / 

n

repeatedly.

Notes

•

If you select “RELOAD” in step 4, no test tones are output.

•

If an error occurs during the “AUTO:CHECK” procedure, the 
setup procedure is canceled and an error screen appears. For 
details, see “If an error screen appears” on page 17.

•

When this unit detects potential problems during the “AUTO 
SETUP” procedure, “WARNING” and the warning messages 
appear after this unit displays the result of the automatic setup. For 
details, refer to the “AUTO SETUP” section in “Troubleshooting” 
on page 41.

•

The distance measurement result may be longer than the actual 
distance depending on the characteristics of your subwoofer.

7

Press 

o

l

 / 

h

 to select “SET” or “CANCEL.”

8

Press 

o

ENTER

 to confirm your selection.

“AUTO SETUP” appears on the front panel display.

9

Press 

k

MENU

 to exit from “SET MENU.”

10

Disconnect the optimizer microphone from 
this unit.

The optimizer microphone is sensitive to heat. Keep it 
away from direct sunlight and do not place it on top 
of this unit.

y

•

If you change speakers, speaker positions, or the layout of your 
listening environment, run “AUTO SETUP” again to recalibrate 
your system.

•

When you want to check the result of the automatic setup in detail 
or manually adjust the parameters, use “MANUAL SETUP” (see 
page 32).

■

If an error screen appears

If this unit detects the potential problems, an error 
message appears on the front panel display during the 
automatic setup.
For details about each error message, see the “AUTO 
SETUP” section in “Troubleshooting” on page 41.
After a few seconds later, the following choices appear.
Press 

o

l

 / 

h

 to select “RETRY” or “EXIT” and then 

press 

o

ENTER

.

■

If “WARNING” appears

When this unit detects potential problems during the 
automatic setup procedure, “WARNING” appears on the 
front panel display after result of each speaker. Check the 
warning messages to correct your speaker settings.

Note

•

Warnings differ from errors in that warnings do not cancel the automatic 
setup procedure.

Press 

o

n

 to display the detailed information 

about the warning.

The detailed information about the warning is displayed 
and the indicators of inapplicable speakers blink on the 
front panel display.

y

•

For details about each warning message, see the “AUTO SETUP” section 
in “Troubleshooting” on page 41.

Choice

Function

SET

*

Confirms the “AUTO SETUP” results.

CANCEL

Cancels the “AUTO SETUP” results.

F L : 3 . 3 m

+ 2

The distance between the speaker 
and the listening position

The result of the 
adjustment of the 
volume level

Speaker

FL/FR: Front left/right

C: Center

SL/SR: Surround left/right

SW: Subwoofer

Choice

Function

RETRY

*

Starts the “AUTO SETUP” again.

EXIT

Exits from the “AUTO SETUP” procedure.

P H A S E R E V E R S E D

LFE

L

C

R

SL

SR

Flashes