Bosch GWS 18 125 V LI 2×4 0Ah - Инструкция по эксплуатации - Страница 22

 English | 

23

Bosch Power Tools

1 

6

0

9

92

A 01F | (10.1.13)

Cutting Stone



Provide for sufficient dust extraction when cutting 

stone.



Wear a dust respirator.



The machine may be used only for dry cutting/grinding.

For cutting stone, it is best to use a diamond cutting disc.

When using the cutting guide with dust extraction protection 
guard 

26

, the vacuum cleaner must be approved for vacuum-

ing masonry dust. Suitable vacuum cleaners are available 
from Bosch.

Switch on the machine 
and place the front part 
of the cutting guide on 
the workpiece. Slide the 
machine with moderate 
feed, adapted to the ma-
terial to be worked.

For cutting expecially hard material, e. g., concrete with high 
pebble content, the diamond cutting disc can overheat and 
become damaged as a result. This is clearly indicated by cir-
cular sparking, rotating with the diamond cutting disc.
In this case, interrupt the cutting process and allow the dia-
mond cutting disc to cool by running the machine for a short 
time at maximum speed with no load.

Noticeable decreasing work progress and circular sparking 
are indications of a diamond cutting disc that has become 
dull. Briefly cutting into abrasive material (e. g. lime-sand 
brick) can resharpen the disc again.

Information on Structures

Slots in structural walls are subject to the Standard DIN 1053 
Part 1, or country-specific regulations.
These regulations are to be observed under all circumstanc-
es. Before beginning work, consult the responsible structural 
engineer, architect or the construction supervisor.

Recommendations for Optimal Handling of the Battery

Protect the battery against moisture and water.

Store the battery only within a temperature range between 
0 ° C and 50 ° C. As an example, do not leave the battery in the 
car in summer.

Occasionally clean the venting slots of the battery using a soft, 
clean and dry brush.

A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.

Observe the notes for disposal.

Maintenance and Service

Maintenance and Cleaning



Before any work on the machine itself (e. g. mainte-

nance, tool change, etc.) as well as during transport 

and storage, remove the battery from the power tool. 

There is danger of injury when unintentionally actuating 
the On/Off switch.



For safe and proper working, always keep the machine 

and ventilation slots clean.

Please store and handle the accessory(-ies) carefully.

If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by 
an after-sales service centre for Bosch power tools.

In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of 
the machine.

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare 
parts. Exploded views and information on spare parts can al-
so be found under:

www.bosch-pt.com

Bosch’s application service team will gladly answer questions 
concerning our products and their accessories.

Great Britain

Robert Bosch Ltd. (B.S.C.)
P.O. Box 

9

8

Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 

9

 5HJ

Tel. Service: (0844) 73

6

010

9

Fax: (0844) 73

6

014

6

E-Mail: boschservicecentre@bosch.com

Ireland

Origo Ltd.
Unit 

2

3 Magna Drive

Magna Business Park
City West
Dublin 

2

4

Tel. Service: (01) 4

666

700

Fax: (01) 4

666

888

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 

66

Clayton South VIC 31

69

Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045

OBJ_BUCH-1102-005.book  Page 23  Thursday, January 10, 2013  11:03 AM