Makita ELM4612 - Инструкция по эксплуатации - Страница 10

10

6) Thoroughly inspect the area where the equipment is to 

be used and remove all objects which can be thrown 
by the machine.

7) Before using, always visually inspect to see that the 

blades, blade bolts and cutter assembly are not worn 
or damaged. Replace worn or damaged blades and 
bolts in sets to preserve balance.

8) Mow only in daylight or in good artificial light.
9) Avoid operating the equipment in wet grass, where 

feasible.

10) Always be sure of your footing on slopes.
11) Walk, never run.
12) For wheeled rotary machines; mow across the face of 

slopes, never up and down.

13) Exercise extreme caution when changing direction on 

slopes.

14) Do not mow excessively on steep slopes.
15) Use extreme caution when reversing or pulling the 

lawn mower towards you.

16) Stop the blade if the lawn mower has to be tilted for 

transportation when crossing surfaces other than 
grass, and when transporting the lawn mower to and 
from the area to be mowed.

17) Never operate the lawn mower with defective guards, 

or without safety devices, for example deflectors and/
or grass catchers, in place.

18) Start or switch on the motor carefully according to 

instructions and with feet well away from the blades.

19) Do not tilt the lawn mower when starting switching on 

the motor, except if the lawn mower has to be tilted for 
starting. In this case, do not tilt it more than absolutely 
necessary and lift only the part which is away from the 
operator.

20) Do not start the motor when standing in front of the 

discharge chute.

21) Do not put hands or feet near or under rotating parts. 

Keep clear of the discharge opening at all times.

22) Never pick up or carry a lawn mower while the motor 

is running.

23) Stop the motor and disconnect the plug:

- before clearing blockages or unclogging chute;
- before checking, cleaning or working on the lawn 

mower;

- after striking a foreign object. Inspect the lawn 

mower for damage and make repairs before 
restarting and operating the lawn mower;

- if lawn mower starts to vibrate abnormally (check 

immediately).

24) Stop the mower:

- whenever you leave the lawn mower.

25) Keep all nuts, blots and screws tight to be sure the 

equipment is in safe working condition.

26) Check the grass catcher frequently for wear or 

deterioration.

27) Replace worn or damaged parts for safety.
28) Do not use the lawn mower if the cords are damaged 

or worn.

29) Do not connect a damaged cord to the supply or touch 

a damaged cord before it is disconnected from the 
supply. A damaged cord can lead to contact with live 
parts.

30) Do not touch the blade before the machine is 

disconnected from the supply and the blade have 
come to a complete stop.

31) To keep extension cords away from the blade. The 

blade can cause damage to the cords and lead to 
contact with live parts.

32) To disconnect the supply (i.e. pulling the plug from the 

socket):
- whenever leaving the machine unattended;
- before clearing a blockage;
- before checking, cleaning or working on the 

machine;

- after striking a foreign object;
- whenever the machine starts vibrating abnormally.

33) Children should be supervised to ensure that they do 

not play with the appliance.

34) This appliance is not intended for use by persons 

(including children) with reduced physical, sensory or 
mental capabilities, or lack of experience and 
knowledge, unless they have been given supervision 
or instruction concerning use of the appliance by a 
person responsible for their safety.

35) If the supply cord is damaged, it must be replaced by a 

special cord or assembly available from the 
manufacturer or its service agent.

36) Instructions for the safe operation of the appliance, 

including a recommendation that the appliance should 
be supplied via a Residual Current Device (RCD) with 
a tripping current of not more than 30 mA.

37) Be careful during adjustment of the machine to 

prevent entrapment of the fingers between moving 
blades and fixed parts of the machine.

38) Always allow the machine to cool before storing.
39) When servicing the blades be aware that, even though 

the power source is switched off, the blades can still 
be moved.

40) Replace worn or damaged parts for safety; Use only 

genuine replacement parts and accessories.

41) Be careful during adjustment of the appliance to 

prevent entrapment of the fingers between moving 
blades and fixed parts of appliance.

42) Before use check the supply and extension cord for 

signs of damage or worn. If the cord becomes 
damaged during use, disconnect the cord from the 
supply immediately. DO NOT TOUCH THE CORD 
BEFORE DISCONNECTING THE SUPPLY. Do not 
use the appliance if the cord is damaged or worn. 

43) If the supply cord is damaged, it must be replaced by 

the manufacturer, its service agent or similarly 
qualified persons in order to avoid a hazard.

3. PARTS DESCRIPTION (Fig. 1, 

Fig. 2)