Sparky MBGS 200 - Инструкция по эксплуатации - Страница 9

7

Original instructions

EN

so that the distance between each one and the wheel 

does not exceed 1.6 mm 

(Fig.11)

. Adjust regularly the 

distance between the wheel and the tool rest as the 

diameter of the wheel decreases with use. This will 

ensure the proper angle for sharpening and hence - 

high efficiency. The tool rests shall be used always in 

horizontal position.

▪

When you switch the machine on let it operate at no 

load until the motor gains full speed.

WARNING:

 Never use accessories or attach-

ments differing from those recommended in this manual.

WARNING:

 Never sharpen or grind parts made 

of aluminium, brass, or copper.

▪

While grinding, rest the machined piece against the 

wheel front surface, do not grind on the wheel flat 

side. Overloading the wheel side surfaces is danger-

ous and must not be attempted.

WARNING:

 In normal brushing operations, the 

material being removed will fly off the brush with consider

-

able force along with brush filaments which break off due 

to fatigue. Do not operate the bench grinder unless the 

eye shields are dropped down or without goggles.

▪

Avoid excessive pressure when using the brush. 

Excessive pressure causes over-bending of the fila-

ments, filament breakage, and reduced brush life.

WARNING:

 Never exceed the recommended 

Maximum Safe Free Speed R.P.M. (MSFS) rating of the 

brush.

▪

Do not continue to use worn, torn or heavily clogged 

sanding belts.

▪

Do not touch the moving sanding belt.

SWITCHING ON - SWITCHING OFF

Switching on: Press the START button “I” of the switch (6).

Switching off: Press the STOP button “O” of the switch (6).

ACCESSORIES

MBG 150, MBG 175, MBG 200, MBG 250: 

Raw wheel - 1 

pc., finishing wheel -1 pc.

MBGT 150: 

Raw wheel - 1 pc., crimped wire wheel brush 

with 0.3 mm brass filaments - 1 pc.

MBGS 200: 

Raw wheel - 1 pc., sanding belt - 1 pc.

WARNING:

 The bench grinder can be oper-

ated with other grit wheels with maximum allowable 

wheel speed  > 3000 min

-1

VII - Maintenance 

WARNING:

 Always ensure that the tool is 

switched off and unplugged before attempting to perform 

inspection or maintenance.

This power tool does not require any special maintenance. 

If the bench grinder should happen to fail despite the care 

taken, please notify the authorised service centres for war-

ranty and post-warranty servicing of SPARKY power tools.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they are properly 

tightened. Should any of the screws be loose, retighten it im-

mediately to avoid hazards. 

If the replacement of the supply cord is necessary, this has 

to be done by the manufacturer or his agent in order to avoid 

a safety hazard.

CLEANING

Clean the spindle and the wheel guards from time to time 

(Fig.12)

. Exterior parts may be cleaned with a damp cloth 

and mild detergent if necessary.

Never use alcohol, petrol or other cleaning agent.

Never use caustic agents to clean plastic parts.

WARNING:

 Water must never come into contact 

with the tool.

VIII - Warranty

The guarantee period for SPARKY power tools is deter-

mined in the guarantee card.

Faults due to normal wear, overloading or improper han

-

dling will be excluded from the guarantee.

Faults due to defective materials implemented as well as 

defects in workmanship will be corrected free of charge 

through replacement or repair.

The complaints for defective SPARKY power tools will 

be recognized if the machine is sent back to the dealer 

or is presented to the authorised warranty service centre 

undismantled, in its initial condition.

Notes

Carefully read the entire original instructions before us-

ing this product.

The manufacturer reserves the right to make changes 

and improvements to the products and to alter specifica

-

tions without prior notice.

Specifications may differ from country to country.

pages-MBG-MBGT-MBGS.indd   7

30.7.2012 г.   15:12:52 ч.