Усилители Yamaha BRX-610 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
SETUP MENU
39
En
Eng
lish
SETTINGS
The default settings are marked with “
*
”.
■
Audio Output
[HDMI]
You can select the output mode of the HDMI terminal.
Bitstream, PCM, Off
*
• To output sound from the speakers, select [Off].
• Sound from your iPod or the audio signal input to the DIGITAL
IN (COAXIAL and OPTICAL) jacks of this unit, cannot be
output to a TV from this unit through the HDMI cable.
• To output HD audio (such as Dolby TrueHD or DTS-HD) from
the HDMI terminal, set [Video Out Select] to [HDMI Auto] or
more than [HDMI 720p] (p. 37).
[DRC]
You can set the DRC (Dynamic Range Compression)
(p. 50) to [On]/[Off]/[Auto]. When set to [Auto], DRC is
automatically turned on for a source with DRC
information in Dolby TrueHD format. DRC makes the
strong sound such as plosive sound lower, and
conversations more audible. It is useful when you watch
movies in the night.
Off
*
, On, Auto
■
Speaker Setting
[Configuration]
You can set the output of 5.1 ch surround depending on
the connected speakers.
1
Press
5
/
a
to select a speaker you want to configure,
then press
ENTER
.
2
Adjust the figures below. Note that some of items are
not displayed depend on the selected speaker.
Size
When the woofer section of a speaker is 16 cm
(6-1/2 in) or larger, select [Large]. When
smaller than 16 cm (6-1/2 in), select [Small].
Large, Small*
Trim
Adjusts the selected speaker’s level (volume
level).
-6 to +6 dB (in 0.5 dB step)
The default setting is 0 dB.
Delay
Separately adjusts the timing at which each
speaker produces audio so that sounds from the
speakers reach the listening position at the same
time.
0.5 to 10 m (in 0.5 m step)
The default setting is 3 m.
Disable
When selected speaker is not in use, select
[Yes].
Yes, No*
3
Press
RETURN
to go back to speaker selection.
[2ch Downmix]
You can select down mix method to 2-ch from [Stereo] or
[Lt/Rt].
Stereo*, Lt/Rt
[Test Tone]
You can check if the speaker setting is correct by
outputting the test tone.
[Subwoofer Size]
You can select the size for your subwoofer speaker to be
[Small] or [Large]. When your subwoofer driver diameter
is more than 20 cm, or when you feel low-frequency and
bass sound is weak, select [Large].
Small*, Large
■
Post Process
[UpMix]
You can multi-channelize the 2-channel audio signal
(effective on speaker output). To multi-channelize, select
[Dolby PLII] or [DTS NEO:6]. You can select [Cinema]
or [Music] when [DTS NEO:6] is selected. Also you can
select [Movie] or [Music] when [Dolby PLII] is selected.
Off*, Dolby PLII, DTS NEO:6
■
System Information
Software version and MAC address (p. 50) are displayed.
Audio Setting
Notes
