Black+Decker BXDH20E - Инструкция по эксплуатации - Страница 9

ENGLISH

(Original instructions)

9

♦ Connect the pipes and carry out a leak test before charging with refrigerant.

♦ Check safety equipment before putting into service.

Maintenance

♦ Portable equipment shall be repaired outside or in a workshop specially equipped for 

servicing units with flammable refrigerants.

♦ Ensure sufficient ventilation at the repair place.

♦ Be aware that malfunction of the equipment may be caused by refrigerant loss and a 

refrigerant leak is possible.

♦ Discharge capacitors in a way that won’t cause any spark. The standard procedure to 

short circuit the capacitor terminals usually creates sparks.

♦ Reassemble sealed enclosures accurately. If seals are worn, replace them.

♦ Check safety equipment before putting into service.

Repair

♦ Portable equipment shall be repaired outside or in a workshop specially equipped for 

servicing units with flammable refrigerants.

♦ Ensure sufficient ventilation at the repair place.

♦ Be aware that malfunction of the equipment may be caused by refrigerant loss and a 

refrigerant leak is possible.

♦ Discharge capacitors in a way that won’t cause any spark.

♦ When brazing is required, the following procedures shall be carried out in the right 

order:

♦ Remove the refrigerant. If the recovery is not required by national regulations, drain

♦ the refrigerant to the outside. Take care that the drained refrigerant will not cause any 

danger. In doubt, one person should guard the outlet. Take special care that drained 

refrigerant will not float back into the building.

♦ Evacuate the refrigerant circuit.

♦ Purge the refrigerant circuit with nitrogen for 5 min.

♦ Evacuate again.

♦ Remove parts to be replaced by cutting, not by flame.

♦ Purge the braze point with nitrogen during the brazing procedure.

♦ Carry out a leak test before charging with refrigerant.

♦ Reassemble sealed enclosures accurately. If seals are worn, replace them.

♦ Check safety equipment before putting into service.

Decommissioning

♦ If the safety is affected when the equipment is putted out of service, the refrigerant 

charge shall be removed before decommissioning.

♦ Ensure sufficient ventilation at the equipment location.

♦ Be aware that malfunction of the equipment may be caused by refrigerant loss and a 

refrigerant leak is possible.

♦ Discharge capacitors in a way that won’t cause any spark.

♦ Remove the refrigerant. If the recovery is not required by national regulations, drain 

the refrigerant to the outside. Take care that the drained refrigerant will not cause any 

danger. In doubt, one person should guard the outlet.

♦ Take special care that drained refrigerant will not float back into the building.

♦ Evacuate the refrigerant circuit.

♦ Purge the refrigerant circuit with nitrogen for 5 min.

♦ Evacuate again.

♦ Fill with nitrogen up to atmospheric pressure.

♦ Put a label on the equipment that the refrigerant is removed.

Disposal

♦ Ensure sufficient ventilation at the working place.

♦ Remove the refrigerant. If the recovery is not required by national regulations, drain 

the refrigerant to the outside. Take care that the drained refrigerant will not cause any 

danger. In doubt, one person should guard the outlet.

♦ Take special care that drained refrigerant will not float back into the building.

♦ Evacuate the refrigerant circuit.

♦ Purge the refrigerant circuit with nitrogen for 5 min.

♦ Evacuate again.

♦

Cut out the compressor and drain the oil.

♦ Transportation, marking and storage for units that employ flammable refrigerants

This appliance complies with Directive 2014/35/EU on Low Voltage, Directive 2014/30/

EU on Electromagnetic Compatibility, Directive 2011/65/EU on the restrictions of the use 

of certain hazardous substances in electrical and electronic equipment and Directive 

2009/125/EC on the ecodesign requirements for energy-related products.