Швейная машина Brother SL-7 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.

12
Reverse Sewing Lever
To sew in reverse, press down the reverse sewing lever as far as
possible and hold it in that position while lightly stepping on the
foot controller. To sew forward, release the reverse sewing lever.
Reverse sewing is used for locking and reinforcing seams.
THREADING THE MACHINE
Winding the Bobbin
1. Place the spool of thread on the spool pin and pass the thread
around the bobbin winding tension disc.
a
Bobbin winding tension disc
b
Bobbin winding
2. Pass the end of the thread through the hole in the bobbin from
the inside.
2. Place the bobbin onto the bobbin winding shaft and slide the
shaft to the right. Turn the bobbin clockwise, by hand, until
the spring on the shaft slides into the slit on the bobbin.
c
Spring
d
Slit
4. While holding the end of the thread, gently press on the foot
controller to wind the thread around the bobbin a few times,
then stop the machine.
3. Trim the excess thread sticking out from the top of the bobbin
and continue winding the thread onto the bobbin by pressing
down on the foot controller.
NOTE:
The machine stops automatically when the bobbin is full.
6. When the machine stops, cut the thread between bobbin and
spool, push the shaft to the left and remove the full bobbin
from the shaft.
CAUTION:
Although the needle bar does not move when the bobbin
winding shaft is slid toward the bobbin presser, the balance
wheel will continue to turn. Therefore, do not touch the balance
wheel while the bobbin is being wound.
Levier de couture en marche arrière
Pour coudre en arrière, abaisser au maximum le levier de couture
en marche arrière, et le maintenir dans cette position tout en
appuyant légèrement sur la pédale. Pour coudre à nouveau vers
l’avant, relâcher le levier. Utiliser la couture en marche arrière
pour arrêter ou renforcer une couture.
ENFILAGE DE LA MACHINE
Remplissage de la canette
1. Placer la bobine de fil sur le porte-bobine et faire passer le fil
par le disque de tension du dévidoir.
a
Disque de tension du dévidoir
b
Remplissage de la canette
2. Passer l’extrémité du fil dans l’orifice de la canette, par
l’intérieur.
3. Placer la canette sur le dévidoir et glisser celui-ci vers le
droite. Tourner la canette dans le sens des aiguilles d’une
montre, à la main, jusqu’à ce que le ressort de la broche se
place dans la rainure de la canette.
c
Ressort
d
Rainure
4. Tout en tenant l’extrémité du fil, appuyer doucement sur la
pédale pour enrouler le fil autour de la canette. Arrêter la
machine au bout de quelques tours.
5. Couper le bout de fil dépassant au-dessus de la canette puis
continuer à enrouler le fil sur la canette en appuyant sur la
pédale du rhéostat.
REMARQUE:
La machine s’arrête automatiquement lorsque la canette est pleine.
6. Lorsque la machine s’arrête, couper le fil entre la canette et la
bobine, pousser le dévidoir vers la gauche et en retirer la
canette pleine.
PRECAUTION:
Bien que la barre à aiguille ne fonctionne pas lorsque la broche
du dévidoir est glissée pour maintenir la canette, le volant à main
va continuer à tourner. Dès lors, éviter de toucher le volant lors
du remplissage de la canette.
Palanca de retroceso
Para coser hacia atrás, baje completamente la palanca de retroceso y
manténgala en esa posición mientras presiona ligeramente el pedal.
Para volver a coser hacia adelante, vuelva a subir la palanca de
retroceso. La costura hacia atrás se usa para terminar y reforzar
costuras.
Клавиша шитья в обратном направлении
Для шитья в обратном направлении нажмите до упора
клавишу шитья в обратном направлении и удерживайте ее в
данном положении, слегка нажимая в это время на педаль.
Для шитья в прямом направлении отпустите клавишу шитья в
обратном направлении. Шитьё в обратном направлении
используется для закрепления и усиления швов.
Содержание
- 9 INDICE; СОДЕРЖАНИЕ
- 11 PIÉCES PRINCIPALES
- 12 ACCESSORIES; ACCESSOIRES; ПРИНАДЛЕЖНОСТИ
- 13 Connecting Plugs; FONCTIONNEMENT DE LA; Raccordement; FUNCIONAMIENTO DE LA; Conexión de los enchufes; РАБОТА НА ШВЕЙНОЙ; Подключение электропитания
- 14 Main Power and Sewing Light Switches; Foot Controller; Interrupteur principal et de la lampe; Interruptor principal y de luz; Выключатель питания и лампочки
- 15 Inserting the Needle; Checking the Needle; Pour mettre l’aiguille en place; Vérification de l’aiguille; Comprobación de la aguja; Установка иглы; Проверка иглы
- 16 Changing the Presser Foot; Cambio del prensatelas; Замена прижимной лапки
- 17 Converting to Free-Arm Style; Steadying the Machine; Modèle bras libre; Pour stabiliser la machine; Para estabilizar la máquina; Переоборудование машины для работы с; Обеспечение устойчивости машины
- 18 ac; VARIOUS CONTROLS; Pattern Selection Dial; DESCRIPTIF DES DIFFERENTES; DISTINTOS MANDOS; Selector de puntadas; ОРГАНЫ УПРАВЛЕНИЯ; Ручка выбора вида строчки
- 20 DIBUJO Y NOMBRE DE LOS PUNTOS
- 21 Reverse Sewing Lever; THREADING THE MACHINE; Winding the Bobbin; Levier de couture en marche arrière; ENFILAGE DE LA MACHINE; Remplissage de la canette; Palanca de retroceso; Клавиша шитья в обратном направлении
- 22 ENHEBRADO DE LA MÁQUINA; Bobinado de la canilla; ЗАПРАВКА НИТИ В МАШИНУ; Намотка шпульки
- 26 Para sacar el hilo de la canilla
- 28 Costura con aguja doble; Шитье двойной иглой; УСТАНОВКА ДВОЙНОЙ ИГЛЫ; ЗАПРАВКА ДВОЙНОЙ ИГЛЫ НИТЬЮ
- 29 Thread Tension; Tension des fils; Tensión de los hilos; Натяжение нитей; Возможные затруднения и методы их разрешения.; AE1 Дисковый регулятор натяжения верхней нити; BE1 Дисковый регулятор натяжения верхней нити
- 30 Слишком слабое натяжение нижней нити.
- 32 TABLA DE RELACIÓN ENTRE TEJIDOS, HILOS Y AGUJAS; ТАБЛИЦА РЕКОМЕНДУЕМЫХ КОМБИНАЦИЙ ТКАНЕЙ,
- 35 Zigzag Stitching; ZIGZAG STITCH; Points zigzag; Puntadas zigzag; Шитьё строчкой «зигзаг»; СТРОЧКА «ЗИГЗАГ»
- 36 Blind Hem Stitching; Point élastique invisible; Puntadas invisibles; Потайная строчкаEмережка
- 37 Elastic Stitching; MENDING; JOINING FABRIC; Point élastique; Puntada elástica; Эластичная строчка; РЕМОНТ ТКАНИ; ПРИШИВАНИЕ ЭЛАСТИЧНОЙ ТЕСЬМЫ; СТАЧИВАНИЕ ТКАНЕЙ
- 38 Shell Tuck Stitching; Point picot; Puntada ondas; СтрочкаEракушка
- 39 Making a Buttonhole; MAKING A BUTTONHOLE; Création d’une boutonnière; Para coser ojales; Выметывание петель; ВЫПОЛНЕНИЕ ВЫМЕТЫВАНИЯ ПЕТЕЛЬ
- 42 ЗАКРЕПЛЕНИЕ СТРОЧКИ И ПРОРЕЗКА ПЕТЛИ
- 43 Buttonhole Fine Adjustment; Equilibrage des boutonnières; Ajuste fino de los ojales; Точная настройка при выметывании
- 44 Button Sewing; Pour coudre un bouton; Coser botones; Пришивание пуговиц
- 45 Zipper Insertion; Insertion de fermeture à glissière; Poner de cremalleras; Вшивание застежки «молния»
- 46 Gathering; Pour froncer un tissu; Fruncido; Выполнение сборок
- 47 Darning; Reprisage; Zurcido; Штопка
- 48 Appliques; Aplicaciones; Аппликации
- 49 Monogramming and Embroidering; PREPARING FOR MONOGRAMMING AND EMBROIDERING; Monogrammes et broderies; Monogramas y bordados; Выстрачивание монограмм и вышивание
- 51 Changing the Bulb; Remplacement de l’ampoule; Cambio de la bombilla; Замена лампочки подсветки
- 52 Removing the Shuttle Hook; Graissage; Engrasado; Смазка
- 53 Cleaning the Shuttle Race; Limpieza; Чистка; Извлечение челнока
- 54 Cleaning the Feed Dogs; Performance Checklist; Liste de vérification en cas de; Listado de posibles incidencias; Очистка гребенок транспортера; Таблица контрольных проверок
- 63 Repacking the Machine; Emballage de la machine; IMPORTANT; Embalaje de la máquina; IMPORTANTE; Повторная упаковка машины; ВАЖНО
- 67 УКАЗАТЕЛЬ