Bosch GWS 24 300 J - Инструкция по эксплуатации - Страница 19

 English | 

19

Bosch Power Tools

3 609 929 B90 | (1.10.09)

g) If devices are provided for the connec-

tion of dust extraction and collection fa-
cilities, ensure these are connected and 
properly used. 

Use of dust collection can 

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. 

The 

correct power tool will do the job better 
and safer at the rate for which it was de-
signed.

b) Do not use the power tool if the switch 

does not turn it on and off. 

Any power 

tool that cannot be controlled with the 
switch is dangerous and must be re-
paired.

c) Disconnect the plug from the power 

source and/or the battery pack from the 
power tool before making any adjust-
ments, changing accessories, or storing 
power tools. 

Such preventive safety 

measures reduce the risk of starting the 
power tool accidentally.

d) Store idle power tools out of the reach of 

children and do not allow persons unfa-
miliar with the power tool or these in-
structions to operate the power tool. 

Power tools are dangerous in the hands of 
untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts, 
breakage of parts and any other condi-
tion that may affect the power tool’s op-
eration. If damaged, have the power tool 
repaired before use. 

Many accidents are 

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. 

Prop-

erly maintained cutting tools with sharp 
cutting edges are less likely to bind and 
are easier to control.

g) Use the power tool, accessories and tool 

bits etc. in accordance with these in-
structions, taking into account the work-
ing conditions and the work to be per-
formed. 

Use of the power tool for 

operations different from those intended 
could result in a hazardous situation.

5) Service

a) Have your power tool serviced by a qual-

ified repair person using only identical 
replacement parts. 

This will ensure that 

the safety of the power tool is maintained.

Safety Warnings for Cut-off Grinder

f

The provided protection guard must be 
safely fastened to the power tool and ad-
justed in such a manner that a maximum on 
safety is achieved, meaning, that the small-
est possible part of the cutting disc faces 
openly toward the operator. 

The protection 

guard is supposed to protect the operator 
against fragments and accidental contact 
with the cutting disc.

f

Use only flat, reinforced cutting discs for 
your power tool. 

Just because the accessory 

can be attached to your power tool, it does 
not assure safe operation.

f

The rated speed of the accessory must be at 
least equal to the maximum speed marked 
on the power tool. 

Accessories running fast-

er than their rated speed can break and fly 
apart.

f

Wheels must be used only for recommend-
ed applications. For example: do not grind 
with the side of cut-off wheel. 

 Abrasive cut-

off wheels are intended for peripheral grind-
ing, side forces applied to these wheels may 
cause them to shatter.

f

Always use undamaged wheel flanges that 
are of correct diameter for your selected 
wheel. 

Proper wheel flanges support the 

wheel thus reducing the possibility of wheel 
breakage.

f

Do not use worn down cutting discs or 
wheels from larger power tools. 

Cutting 

discs for larger power tools are not designed 
for the higher speeds of smaller power tools 
and can break apart.

f

The outside diameter and the thickness of 
your accessory must be within the capacity 
rating of your power tool. 

Incorrectly sized 

accessories cannot be adequately guarded 
or controlled.

OBJ_BUCH-280-002.book  Page 19  Thursday, October 1, 2009  9:57 AM