Bosch SDS Plus GBH 36 FV LI - Инструкция по эксплуатации - Страница 18

18

 | English 

1 609 929 V40 | (17.8.11)

Bosch Power Tools

Pay attention that the clamping band of the auxiliary handle is 

positioned in the groove on the housing as intended for.

Adjusting the Drilling Depth (see figure B)

The required drilling depth 

X

 can be set with the depth stop 

18

.

– Press the button for the depth stop adjustment 

13

 and in-

sert the depth stop into the auxiliary handle 

19

.

The knurled surface of the depth stop 

18

 must face down-

ward.

– Insert the SDS-plus drilling tool to the stop into the SDS-

plus tool holder 

3

. Otherwise, the movability of the SDS-

plus drilling tool can lead to incorrect adjustment of the 

drilling depth.

– Pull out the depth stop until the distance between the tip of 

the drill bit and the tip of the depth stop correspond with 

the desired drilling depth 

X

.

Selecting Drill Chucks and Tools

For hammer drilling and chiselling, SDS-plus tools are re-

quired that are inserted in the SDS-plus drill chuck.
For drilling without impact in wood, metal, ceramic and plas-

tic as well as for screwdriving, tools without SDS-plus are 

used (e. g., drills with cylindrical shank). For these tools, a 

keyless chuck or a key type drill chuck are required.
GBH 36 VF-LI: The SDS-plus quick change chuck 

2

 can easily 

be replaced against the quick change keyless chuck 

1

 provid-

ed.

Changing the Key Type Drill Chuck (GBH 36 V-LI)

To work with tools without SDS-plus (e. g., drills with cylindri-

cal shank), a suitable drill chuck must be mounted (key type 

drill chuck or keyless chuck, accessories).

Mounting the Key Type Drill Chuck (see figure C)

– Screw the SDS-plus adapter shank 

22

 into a key type drill 

chuck 

21

. Secure the key type drill chuck 

21

 with the se-

curing screw 

20

. 

Please observe that the securing 

screw has a left-hand thread.

Inserting the Key Type Drill Chuck (see figure D)

– Clean the shank end of the adapter shank and apply a light 

coat of grease.

– Insert the key type drill chuck with the adapter shank into 

the tool holder with a turning motion until it automatically 

locks.

– Check the locking effect by pulling the key type drill chuck.

Removing the Key Type Drill Chuck

– Push the locking sleeve 

5

 toward the rear and pull out the 

key type drill chuck 

21

.

Removing/Inserting the Quick Change Chuck 

(GBH 36 VF-LI)

Removing the Quick Change Chuck (see figure E)

– Pull the lock ring for the quick change chuck 

6

 toward the 

rear, hold it in this position and pull off the SDS-plus quick 

change chuck 

2

 or the quick change keyless chuck 

1

 to-

ward the front.

– After removing, protect the replacement chuck against 

contamination.

Inserting the Quick Change Chuck (see figure F)

– Before inserting, clean the quick change chuck and apply a 

light coat of grease to the shank end.

– Grasp the SDS-plus quick change chuck 

2

 or the quick 

change keyless chuck 

1

 completely with your hand. Slide 

the quick change chuck with a turning motion onto the drill 

chuck mounting 

23

 until a distinct latching noise is heard.

– The quick change chuck is automatically locked. Check the 

locking effect by pulling the quick change chuck.

Changing the Tool

The dust protection cap 

4

 largely prevents the entry of drilling 

dust into the tool holder during operation. When inserting the 

tool, take care that the dust protection cap 

4

 is not damaged.

f

A damaged dust protection cap should be changed im-

mediately. We recommend having this carried out by 

an after-sales service.

Inserting SDS-plus Drilling Tools (see figure G)

The SDS-plus drill chuck allows for simple and convenient 

changing of drilling tools without the use of additional tools.
– GBH 36 VF-LI: Insert the SDS-plus quick change chuck 

2

.

– Clean and lightly grease the shank end of the tool.

– Insert the tool in a twisting manner into the tool holder until 

it latches itself.

– Check the latching by pulling the tool.
As a requirement of the system, the SDS-plus drilling tool can 

move freely. This causes a certain radial run-out at no-load, 

which has no effect on the accuracy of the drill hole, as the 

drill bit centres itself upon drilling.

Removing SDS-plus Drilling Tools (see figure H)

– Push back the locking sleeve 

5

 and remove the tool.

Inserting Drilling Tools without SDS-plus (GBH 36 V-LI)
Note: 

Do not use tools without SDS-plus for hammer drilling 

or chiselling! Tools without SDS-plus and their drill chucks are 

damaged by hammer drilling or chiselling.
– Insert a key type drill chuck 

21

 (see “Changing the Key 

Type Drill Chuck”, page 18).

– Open the key type drill chuck 

21

 by turning until the tool 

can be inserted. Insert the tool.

– Insert the chuck key into the corresponding holes of the 

key type drill chuck 

21

 and clamp the tool uniformly.

– Turn the mode selector switch 

11

 to the “drilling” position.

Removing Drilling Tools without SDS-plus (GBH 36 V-LI)

– Turn the sleeve of the key type drill chuck 

21

 with the drill 

chuck key in anticlockwise direction until the drilling tool 

can be removed.

Inserting Drilling Tools without SDS-plus (GBH 36 VF-LI) 

(see figure I)
Note: 

Do not use tools without SDS-plus for hammer drilling 

or chiselling! Tools without SDS-plus and their drill chucks are 

damaged by hammer drilling or chiselling.
– Insert the quick change keyless chuck 

1

.

OBJ_BUCH-283-005.book  Page 18  Wednesday, August 17, 2011  7:50 AM