Bosch SDS Plus GBH 36 FV LI - Инструкция по эксплуатации - Страница 17

 English | 

17

Bosch Power Tools

1 609 929 V40 | (17.8.11)

nificantly reduce the exposure level over the total working pe-

riod.

Identify additional safety measures to protect the operator 

from the effects of vibration such as: maintain the tool and the 

accessories, keep the hands warm, organisation of work pat-

terns. 

Declaration of Conformity

We declare under our sole responsibility that the product de-

scribed under “Technical Data” is in conformity with the fol-

lowing standards or standardization documents: EN 60745 

according to the provisions of the directives 2011/65/EU, 

2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:

Robert Bosch GmbH, PT/ESC,

D-70745 Leinfelden-Echterdingen

Robert Bosch GmbH, Power Tools Division 

D-70745 Leinfelden-Echterdingen 

Leinfelden, 17.08.2011

Assembly

Battery Charging

f

Use only the battery chargers listed on the accessories 

page. 

Only these battery chargers are matched to the lith-

ium ion battery of your power tool.

Note: 

The battery is supplied partially charged. To ensure full 

capacity of the battery, completely charge the battery in the 

battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-

ducing its service life. Interrupting the charging procedure 

does not damage the battery.
The lithium-ion battery is protected against deep discharging 

by the “Electronic Cell Protection (ECP)”. When the battery is 

empty, the machine is switched off by means of a protective 

circuit: The inserted tool no longer rotates.

Do not continue to press the On/Off 

switch after the machine has been au-

tomatically switched off. 

The battery can be damaged.

Removing the Battery

The battery 

17

 is equipped with two locking levels that should 

prevent the battery from falling out when pushing the battery 

unlocking button 

12

 unintentionally. As long as the battery is 

inserted in the power tool, it is held in position by means of a 

spring.

To remove the battery 

17

:

– Push the battery against the base of the power tool (1.) 

and at the same time press the battery unlocking button 

12

(2.).

– Pull the battery out of the power tool until a red stripe be-

comes visible (3.).

– Press the battery unlocking button 

12

 again and pull out 

the battery completely.

Battery Charge-control Indication

The three green LEDs of the battery charge-control indicator 

15

 indicate the charge condition of the battery 

17

. For safety 

reasons, it is only possible to check the status of the charge 

condition when the machine is at a standstill.
– Push button 

16

 to indicate the charge condition (also pos-

sible when the battery is removed). The battery charge-

control indicator automatically goes out after approx. 

5 seconds.

When no LED lights up after pushing button 

16

, then the bat-

tery is defective and must be replaced.
During the charging procedure, the three green LEDs light up 

one after the other and briefly go out. The battery is fully 

charged when the three green LEDs light up continuously. The 

three LEDs go out again approx. 5 minutes after the battery 

has been fully charged.
The battery is equipped with a NTC temperature control 

which allows charging only within a temperature range of be-

tween 0 ° C and 45 ° C. A long battery service life is achieved 

in this manner.

Auxiliary Handle

f

Operate your machine only with the auxiliary handle 

19.

Changing the position of the auxiliary handle 

(see figure A)

The auxiliary handle 

19

 can be set to any position for a secure 

and low-fatigue working posture.
– Turn the bottom part of the auxiliary handle 

19

 in counter-

clockwise direction and swivel the auxiliary handle 

19

 to 

the desired position. Then retighten the bottom part of the 

auxiliary handle 

19

 by turning in clockwise direction.

Dr. Egbert Schneider

Senior Vice President

Engineering

Dr. Eckerhard Strötgen

Head of Product

Certification

WARNING

LED

Capacity

Continuous lighting 3 x green

≥

2/3

Continuous lighting 2 x green

≥

1/3

Continuous lighting 1 x green

< 1/3

Flashing light 1 x green

Reserve

OBJ_BUCH-283-005.book  Page 17  Wednesday, August 17, 2011  7:50 AM