Ryobi RCS36B35HI 5133002761 - Инструкция по эксплуатации - Страница 9

7

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

knob until nearly tight, turn the chain tension adjustment 
ring until the saw chain is properly tensioned. The guide 
bar must then be pushed upwards, check chain tension 
again, do not tension the chain too tight.

8.  After the chain is well-tensioned, tighten the knob 

again.

ADJUSTING THE CHAIN TENSION

See page 247. See page 257.

1.  Loosen the chain tensioner knob slightly by turning it 

counterclockwise.

2.  To increase the chain tension, turn the chain tensioner 

adjustment ring clockwise and check the chain tension 
frequently. To reduce the chain tension, turn the chain 
tensioner adjustment ring counterclockwise and check 
the chain tension frequently.

3.  The chain tension is correct when the gap between the 

cutter in the chain and the bar is between 3 mm - 4 
mm. Pull the chain in the middle of the lower side of the 
bar downwards (away from the bar) and measure the 
distance between the bar and the chain cutters.

4.  Tighten the chain tensioner knob by turning it clockwise.

OPERATION

ADDING CHAIN LUBRICATING OIL

See page 246.

 WARNING

Never work without chain lubricant. If the saw chain is 
running without lubricant, guide bar and saw chain can 
be damaged. It is therefore essential to check the oil 
level in the oil level gauge frequently and every time 
before starting to use the chain saw.

1. Clear surface around the oil cap to prevent 

contamination.

2.  Unscrew and remove the cap from the oil tank.
3.  Pour the oil into the oil tank and monitor the oil level 

gauge. Ensure that no dirt enters the oil tank while 
filling.

4.  Put the oil cap back on and tighten it up. Wipe away 

any spillage.

5.  One full oil tank will enable you to use the saw for 20- 

40 min.

Recommended chain lubricating oil

Ŷ

The manufacturer recommends you use only Ryobi 
chainsaw lubricating oil. (Available from your authorised 
Ryobi service centre)

INSTALLING BATTERY PACK

See page 246.

1.  Place the battery pack in the chain saw. Align raised 

ribs on battery pack with grooves in the chain saw’s 
battery port.

2.  Make sure the latch on bottom of the battery pack 

snaps in place and that battery pack is fully seated and 
secure in the chain saw before beginning operation.

HOLDING THE CHAIN SAW

See page 247.

Always hold the chain saw with your right hand at the rear 
handle and your left hand at the front handle. Grip both 
handles with the thumbs and 

¿

 ngers encircling the handles. 

Ensure that your left hand is holding the front handle so 
that your thumb is underneath.

STARTING THE CHAIN SAW

See page 247.

1.  Before starting for operation, you should install the 

battery pack in the machine, and make sure chain 
brake is in run position by pulling chain brake lever /
hand guard toward the front handle.

2.  To start the machine: pull the trigger release, and then 

press the throttle trigger.

CHECKING AND OPERATING CHAIN BRAKE

1.  Engage the chain brake by rotating your left hand 

around the front handle. Allow the back of your hand to 
push the chain brake lever/hand guard toward the bar 
while the chain is rotating rapidly. Be sure to maintain 
both hands on the saw handles at all times.

2.  Reset the chain brake back into the Run position by 

grasping the top of the chain brake lever / hand guard 
and pulling toward the front handle until you hear a 
click.

 WARNING

If the chain brake does not stop the chain immediately, or 
if the chain brake will not stay in the run position without 
assistance, take the saw to an authorised service centre 
for repair prior to use.

TRANSPORTATION AND STORAGE

See page 259 - 260.

Ŷ

Stop the machine, remove the battery pack and allow 
the tool to cool before storing or transporting.

Ŷ

Clean all foreign material from the product. Store it in 
a cool dry and well-ventilated place that is inaccessible 
to children. Keep away from corrosive agents such 
as garden chemicals and de-icing salts. Do not store 
outdoors.

Ŷ

Fit guide bar cover before storing the unit, or during 
transportation.

Ŷ

For transportation, secure the machine against 
movement or falling to prevent injury to persons or 
damage to the machine.

MAINTENANCE

 WARNING

Use only original manufacturer’s replacement parts, 
accessories and attachments. Failure to do so can 
cause possible injury, poor performance and may void 
your warranty.