Einhell GE-BC 33 AS - Инструкция по эксплуатации - Страница 27

GB

- 27 -

Mowing

When mowing, you want to cut all the vegetation 

down to the ground. To do this, set the line spool 

at an angle of 30° to the right. Place the handle in 

the required position. Remember the increased 

risk of injury to the user, watchers and animals, 

and the danger of damaging property due to ob-

jects (for example stones) being thrown up (Fig. 

29).

Warning!

 Do not use the equipment to remove 

objects from footpaths, etc. The equipment is a 

powerful tool and can throw small stones and 

other objects a distance of 15 meters or more, 

causing injuries and damage to cars, houses and 

windows.

Sawing

The equipment is not suitable for sawing.

Jamming

If the cutting blade jams as a result of attempting 

to cut vegetation that is too dense, switch o

ff

  the 

engine immediately. Remove the grass and scrub 

from the equipment before you restart it.

Preventing recoil

When you work with the blade, there is a risk of 

recoil if it strikes solid objects such as tree trunks, 

branches, tree stumps, stones or the like. This will 

throw the equipment backwards in the direction 

opposite to the rotation of the tool. This can cause 

you to lose control of the equipment. Do not use 

the blade near fences, metal posts, boundary 

stones or foundations. For cutting dense stalks, 

position the blade as shown in Fig. 30 to prevent 

recoil.

9. Maintenance

Always switch o

ff

  the equipment and pull out 

the spark boot plug (13) before carrying out any 

maintenance work.

9.1 Replacing the line spool/cutting line

1.  Dismantle the line spool (3) as described in 

section 5.6. Press the spool together (Fig. 35) 

and remove one half of the housing (Fig. 36). 

2.  Take the spool plate (K) out of the line spool 

housing (Fig. 37).

3.  Remove any remaining cutting line.

4.  Place the new cutting line in the center and 

hang the loop which has formed into the re-

cess in the spool splitter. (Fig. 38)

5.  Wind the line onto the spool counter-clockwi-

se and under tension. The spool splitter will 

separate the two halves of the line. (Fig. 39)

6.  Hook the last 15cm of the two ends of the 

line onto the opposite lying line holders of the 

spool plate. (Fig. 40)

7.  Thread the two ends of the line through the 

metal eyelets in the line spool housing (Fig. 

36).

8.  Press the spool plate into the line spool 

housing (Fig. 36).

9.  Pull the two line ends sharply to release them 

from the line holders.

10.  Join the housing parts together again.

11.  Cut the excess line to a length of around 

13cm. This will reduce the load on the engine 

when starting and warming up.

12.  Remount the line spool (see section 5.6). If 

you are replacing the complete line spool, 

skip points 3-6.

9.2 Grinding the safety hood blade

The safety hood blade can become blunt over 

time. When you notice this, undo the screw hol-

ding the safety hood blade on the safety hood. 

Clamp the blade in a vise. Sharpen the blade with 

a 

fl

 at 

fi

 le and make sure that the angle of the cut-

ting edge is not altered in the process. File in one 

direction only.

Anl_GE_BC_33_AS_SPK1.indb   27

Anl_GE_BC_33_AS_SPK1.indb   27

15.10.13   11:56

15.10.13   11:56