Einhell GE-BC 33 AS - Инструкция по эксплуатации - Страница 25

GB

- 25 -

6. Before starting

Each time before use, check the following:

• 

That there are no leaks in the fuel system.

• 

That the equipment is in perfect condition and 

that the safety devices and cutting devices 

are complete.

• 

That all screws are securely fastened.

• 

That all moving parts move smoothly.

6.1 Fuel and oil

Recommended fuels

Use only a mixture of unleaded petrol and special 

2-stroke engine oil. Mix the fuel mixture as indica-

ted in the fuel mixing table.

Important: Do not use a fuel mixture which has 

been stored for longer than 90 days. Important: 

Never use 2-stroke oil with a recommended mi-

xing ratio of 100:1. The manufacturer’s warranty 

will be voided in case of engine damage due to 

inadequate lubrication. Important: Only use con-

tainers designed and approved for the purpose to 

transport and store fuel.

Pour the correct quantities of petrol and 2-stroke 

oil into the mixing bottle (see scale printed on the 

bottle). Then shake the bottle well.

6.2 Fuel mixing table

Mixing procedure: 40 parts petrol to 1 part oil

Petrol

2-stroke oil

1 liter

25 ml

5 liters

125 ml

7. Operation

Please note that the statutory regulations gover-

ning noise abatement may di

ff

 er from one loca-

tion to another.

Before starting up the equipment remove the  pro-

tective caps from the cutting blade.

7.1 Starting with a cold engine

Fill the tank with the required amount of oil/petrol 

mix. See „Fuel and oil“.

1.  Set the equipment down on a hard, level sur-

face.

2.  Press the fuel pump (primer) (Fig. 2/Item 29) 

10 times.

3.  Move the On/O

ff

  switch (Fig. 2/Item 9) to „I“.

4.  Set the choke lever (Fig. 2/Item 17) to I   I.

5.  Hold the equipment 

fi

 rmly and pull out the 

starter cable (Fig. 2/Item 14) until you feel it 

begin to resist. Then tug sharply on the starter 

cable 2 times. 

6.  Set the choke lever (Fig. 2/Item 17) to I   I.

7.  Hold the equipment 

fi

 rmly and pull out the 

starter cable (Fig. 2/Item 14) until you feel it 

begin to resist. Then tug sharply on the starter 

cable 4 times. The equipment should start. 

Important: Never allow the starter line to snap 

back. This may result in damage. 

Once the engine has started, allow the equip-

ment to warm up for 10 seconds. 

Important: Since the choke lever is secured, 

the cutting tool starts to operate when the 

engine is started. 

Then release the choke lever by actuating the 

throttle lever once.

8.  If the engine does not start up, repeat steps 

4-8 above.

Please note: If the engine does not start up even 

after several attempts, read the section „Engine 

troubleshooting“.

Please note: Always pull the starter cord out in 

a straight line. If it is pulled out at an angle, then 

friction will occur on the eyelet. As a result of this 

friction, the cable will become frayed and will 

wear away faster. Always hold the starter handle 

when the cable retracts.

Never allow the cable to snap back when it has 

been pulled out.

7.2 Starting with a warm engine

(The equipment has been idle for less than 15-20 

min.)

1.  Set the equipment down on a hard, level sur-

face.

2.  Switch the On/Of switch to „I“.

3.  Hold the equipment 

fi

 rmly and pull out the 

starter cable until you feel it start to resist. 

Then tug sharply on the starter cable. The 

equipment should start after 1-2 tugs. If the 

equipment does not start after 6 pulls, repeat 

steps 1 – 8 of the procedure for starting the 

engine from cold.

Anl_GE_BC_33_AS_SPK1.indb   25

Anl_GE_BC_33_AS_SPK1.indb   25

15.10.13   11:56

15.10.13   11:56