Bosch GCT 115 Professional - Инструкция по эксплуатации - Страница 15

 English | 

15

Bosch Power Tools

2 610 017 516 | (3.11.11)

f

Maintain a firm grip on the power tool and position your 

body and arm to allow you to resist kickback forces. Al-

ways use auxiliary handle, if provided, for maximum 

control over kickback or torque reaction during 

start-up. 

The operator can control torque reactions or 

kickback forces, if proper precautions are taken.

f

Never place your hand near the rotating accessory. 

Ac-

cessory may kickback over your hand.

f

Do not position your body in line with the rotating 

wheel. 

Kickback will propel the tool in direction opposite 

to the wheel’s movement at the point of snagging.

f

Use special care when working corners, sharp edges, 

etc. Avoid bouncing and snagging the accessory. 

Cor-

ners, sharp edges or bouncing have a tendency to snag the 

rotating accessory and cause loss of control or kickback.

f

Do not attach a saw chain, woodcarving blade, seg-

mented diamond wheel with a peripheral gap greater 

than 10 mm or toothed saw blade. 

Such blades create 

frequent kickback and loss of control.

f

Do not “jam” the wheel or apply excessive pressure. Do 

not attempt to make an excessive depth of cut.  

Over-

stressing the wheel increases the loading and susceptibili-

ty to twisting or binding of the wheel in the cut and the pos-

sibility of kickback or wheel breakage.

f

When wheel is binding or when interrupting a cut for 

any reason, switch off the power tool and hold the pow-

er tool motionless until the wheel comes to a complete 

stop. Never attempt to remove the wheel from the cut 

while the wheel is in motion otherwise kickback may 

occur. 

Investigate and take corrective action to eliminate 

the cause of wheel binding.

f

Do not restart the cutting operation in the workpiece. 

Let the wheel reach full speed and carefully re-enter 

the cut. 

The wheel may bind, walk up or kickback if the 

power tool is restarted in the workpiece.

f

Support panels or any oversized workpiece to minimize 

the risk of wheel pinching and kickback. 

Large work-

pieces tend to sag under their own weight. Supports must 

be placed under the workpiece near the line of cut and near 

the edge of the workpiece on both sides of the wheel.

f

Use extra caution when making a “pocket cut” into ex-

isting walls or other blind areas. 

The protruding wheel 

may cut gas or water pipes, electrical wiring or objects that 

can cause kickback.

Additional safety warnings

f

Use clamps or another practical way to secure and sup-

port the workpiece to a stable platform. 

Holding the 

work by your hand or against the body leaves it unstable 

and may lead to loss of control.

f

Use suitable detectors to determine if utility lines are 

hidden in the work area or call the local utility company 

for assistance. 

Contact with electric lines can lead to fire 

and electric shock. Damaging a gas line can lead to explo-

sion. Penetrating a water line causes property damage or 

may cause an electric shock.

f

Do not touch the cutting disc after working before it 

has cooled. 

The cutting disc becomes very hot while work-

ing.

f

When working with the machine, always hold it firmly 

with both hands and provide for a secure stance. 

The 

power tool is guided more secure with both hands.

Products sold in GB only

: Your product is fitted with an 

BS 1363/A approved electric plug with internal fuse (ASTA 

approved to BS 1362).

If the plug is not suitable for your socket outlets, it should be 

cut off and an appropriate plug fitted in its place by an author-

ised customer service agent. The replacement plug should 

have the same fuse rating as the original plug.

The severed plug must be disposed of to avoid a possible 

shock hazard and should never be inserted into a mains sock-

et elsewhere.

Products sold in AUS and NZ only

: Use a residual current de-

vice (RCD) with a rated residual current of 30 mA or less.

Symbols

The following symbols can be important for the operation of 

your power tool. Please memorise the symbols and their 

meanings. The correct interpretation of the symbols helps 

you operate the power tool better and more secure.

Product Description and 

Specifications

Read all safety warnings and all instruc-

tions. 

Failure to follow the warnings and in-

structions may result in electric shock, fire 

and/or serious injury.

While reading the operating instructions, unfold the graphics 

page for the machine and leave it open.

Intended Use

The machine is intended for cutting and drilling tiles (ceramic, 

granite, marble, fine stoneware, natural stone) without the 

use of water.

Symbols and their meaning

Wear safety goggles.

Wear ear protectors. 

Exposure to noise 

can cause hearing loss.

Wear a dust respirator.

OBJ_BUCH-1502-001.book  Page 15  Thursday, November 3, 2011  3:02 PM