Makita DRC 200 Z - Инструкция по эксплуатации - Страница 17

17 ENGLISH

 lamp flashes 

4 times for each 

sequence

•  Threads and hairs are tangled with the 

drive wheels.

  Remove them from the drive wheels 

(Fig. M-2).

•  The Robotic Cleaner passed through 

a confined area where its top surface 

was pushed down.

  This is not a malfunction.

 lamp flashes 5 

or 7 times for each 

sequence

•  The Robotic Cleaner has overheated.

  Turn the Robotic Cleaner OFF, 

remove the battery cartridge(s), and 

wait for an hour. Use the Robotic 

Cleaner only at room temperatures 

not exceeding 40°C (104°F).

 and 

lamps flash once 

for each sequence

•  The dust box or the filter has not been 

installed.

  Install the dust box or the filter.

 and 

all   lamps flash 

once for each 

sequence

•  The remaining battery charge was 

not enough (

 or 

) to start 

cleaning.

  Fully charge the battery cartridges.

 and   lamps 

light up

•  Threads and hairs are tangled in the 

drive wheels.

  Remove them from the drive wheels 

(Fig. M-2).

•  The Robotic Cleaner passed through 

a confined area where its top surface 

was pushed down.

  This is not a malfunction.

 and   lamps 

light up

•  A sensor error has occurred.

  Turn the Robotic Cleaner OFF and 

then ON.

 and   lamps 

light up

•  An error has occurred in the Robotic 

Cleaner.

  Turn the Robotic Cleaner OFF and 

then ON.

 lamp flashes 

once for each 

sequence

•  Threads and hairs are tangled in the 

side brushes and main brush.

  Remove them from the brushes (Figs. 

A, N-3).

 lamp 

lights up

•  The dust box is full of dust and dirt or 

the filter is clogged.

  Empty the dust box (Fig. K-2) and 

clean the filter (Fig. K-5).

TROUBLESHOOTING

NOTE: If the problem persists after the remedial 

action is taken, consult your nearest Makita Service 

Center.

Symptom

Cause/Remedy

The lamps do 

not light up 

when you press 

the   button.
The Robotic 

Cleaner does not 

operate when you 

press the button 

on the Robotic 

Cleaner or the 

remote control.

  Install the battery cartridges correctly.

  Fully charge the battery cartridges.

  Press the   button to turn the 

Robotic Cleaner ON.

The Robotic 

Cleaner does not 

operate.

  If the 

 Troubleshooting 

lamp, 

 Filter maintenance lamp, 

or 

 Brush maintenance lamp lights 

up or flashes, see “RESTORING THE 

ROBOTIC CLEANER” to resolve the 

problem.

  If the pilot lamp flashes slowly, press 

and hold the   POWER button on 

the Robotic Cleaner until all indicators 

go off, or press the   POWER OFF 

button on the remote control to clear 

the timer.

The Robotic 

Cleaner starts 

operation 

automatically.

•  The auto-on timer has been activated.

The Robotic 

Cleaner stops 

operation during 

cleaning.

  Turn the Robotic Cleaner OFF, and 

then remove any cords, strings, etc. 

from the drive wheels.

  If the Robotic Cleaner has gotten 

stuck on a barrier or other obstacle, 

move the Robotic Cleaner to a 

different location.

The cruising speed 

is not constant.

•  If an obstacle is detected, the Robotic 

Cleaner will slow down as it takes time 

to calculate a traveling direction. This 

is not a malfunction of the Robotic 

Cleaner.

The Robotic 

Cleaner does not 

travel straight 

forward.

  Turn the Robotic Cleaner OFF, and 

then remove any foreign objects 

tangled in the drive wheels.

  Clean the ultrasonic sensors.

The Robotic 

Cleaner is hitting 

obstacles more 

frequently than 

before.

  Clean the ultrasonic sensors.

The Robotic 

Cleaner falls down 

stairs or to a lower 

floor.

  Clean the cliff sensors.

•  The Robotic Cleaner may not avoid 

differences in level of 5.5 cm or 

less. This is not a malfunction of the 

Robotic Cleaner.

The operating 

sound is louder 

than usual.

  Empty the dust box and clean the 

filter, the side brushes, and the main 

brush.