Электропилы Ryobi RCS3840T POWR ХТ (5133002387) - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
English
TROUBLESHOOTING
Problem
Possible cause
Solution
Engine will not start (Make
sure ignition switch is in start
position “I”).
No spark.
The spark plug could be cracked or damaged. Replace
the old spark plug with a new one and try to start again.
If engine will still not start, return the product to an
authorised service centre for further checking.
Flooded engine.
With the ignition switch off, remove spark plug. Move
choke lever to run position (pushed in completely) and pull
starter grip 15 to 20 times. This will clear excess fuel from
engine. Clean and reinstall spark plug. Set ignition switch
to run (I) position. Push and fully release primer bulb 10
times. Pull starter grip three times with choke lever at run.
If engine does not start, move choke lever to choke and
repeat normal starting procedure. If engine still fails to
start, repeat procedure with a new spark plug.
Engine starts but will not
accelerate properly.
Carburettor requires “L” (Low jet)
adjustment.
Contact an authorised service centre for carburettor
adjustment.
Engine starts but will not run
roperly at high speed.
Carburettor requires “H” (High jet)
adjustment.
Contact an authorised service centre for carburettor
adjustment.
Engine does not reach full speed
and/or emits excessive smoke.
Check lubricant fuel mixture.
Use fresh fuel and the correct 2-stroke lubricant mix ratio.
$LU¿OWHUGLUW\
&OHDQWKHDLU¿OWHU
Spark arrester screen dirty.
Clean the spark arrester screen.
Carburettor requires “H” (High jet)
adjustment.
Contact an authorised service centre for carburettor
adjustment.
Engine starts, runs, and
accelerates but will not idle.
Carburettor requires adjustment.
Contact an authorised service centre for carburettor
adjustment.
Engine starts and runs, but chain
is not rotating.
Chain lubricant tank empty.
/XEULFDQWWDQNVKRXOGEH¿OOHGHYHU\WLPH
Check chain tension for overtight
condition.
Tension the chain.
Check for lubricating function.
Run at half throttle 30 to 45 seconds. Stop saw and
check for lubricant dripping from guide bar. If lubricant is
present, the chain may be dull or bar may be damaged.
If no lubricant is on the guide bar, contact an authorised
service centre.
Bar and chain running hot and
smoking.
Chain brake engaged.
Release the chain brake.
Chain tension too tight.
Tension the chain.
Check guide bar and chain for damage.
Inspect the guide bar and chain for damage.
Engine dies during normal
operation and will not restart.
Product set to anti-freeze mode at
normal temperatures.
Set the product to normal operating mode. Allow the
engine to cool down before restarting.
Engine will not start or does not
reach full speed.
Product set to anti-freeze mode at
normal temperatures.
Set the product to normal operating mode.
Engine does not reach full speed
at low temperatures.
Product set to normal mode at low
temperatures.
Set the product to anti-freeze mode.
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
