FALMEC INDUCTION HOB INOX (880) - Инструкция по эксплуатации - Страница 20

20

.

Unconfigured in-

duction module (all 

induction module 

answer to UI, but 

any element is rela-

ted to the effected 

cooking zone.)

induction module 

is not configured

Delete the hob configu-

ration and activate the 

manual configuration. 

Start the UI service 

menu to configure the 

induction module if the 

listed points are not 

successful replace the 

module.

.

No communication 

between UI and 

induction module

No power supply 

of induction 

module.

Bad cabling or 

defect

Check power and LIN 

connections. If con-

nection is OK, replace 

the module

.

Main power distur-

bance

1. Failure in main 

power frequency 

detection

2. Overvoltage

Check main power 

voltage and frequency, 

if ok replace the module

.

Non assignable 

failure

Replace module or User 

interface

.

Fan failure

Fan or control 

electronic is defect

Replace the module

.

Defect ive tempe-

rature probe on 

inductor

Sensor signal out 

of valid range; sen-

sor or electronic is 

defect

Replace the module

.

Hardware defect of 

induction module

Defect hardware 

device detected 

by the self-check 

of the module

Replace the module

.

Configuration failure 2 cooking zones 

are delicated to 

the same element 

of the UI

Delete the actual confi-

guration

manual configuration 

with service menu

.

Fixed sensor value 

(test function for T 

probe on inductor)

Not enough tem-

perature change 

(10 K) within 5 min 

after switch on 

the hob

System must cool down

No 

functiona-

lity and no 

displaying

Overvoltage on 

the switch mode 

power supply (no 

functionality)

400 V connection

Disconnect and correct 

the power line con-

nection

Note:

Not each failure can be delected automatically by the system, e.g. in case of defect of the 

User interface power supply.

WHAT TO DO IN CASE OF PROBLEMS

The cooker or cooking areas do not turn on:

· The cooker is not connected to the electric network.

· The protection fuse is released.

· Check if the block is not active.

· Keys are covered with water or grease.

· An object is placed on the keys.

The symbol is displayed 

.

· There is no saucepan on the cooking area.

· The container used is not compatible with cooktops.

· The diameter of the saucepan bottom is too small compared to the cooking area.

The symbol [E] is displayed:

· Disconnect and connect the cooker.

· Contact the after-sales centre.

One of the area or the entire cooker turns off:

· The safety overheating system is active;

· The cooker or one cooking area remains on for too long;

· one or more keys are covered;

· one of the saucepans is empty and the bottom overheated.

The fan keeps on working after the cooker shutdown:

· This is not a malfunction: the fan keeps on protecting the electronic power unit of the 

device.

· The fan stops automatically.

10 ERROR CODES

For supporting a service technician in case of error, the UI displays error codes.

In combination with the provided document "error codes Basic 2" which includes datai-

led information a complete error matrix description is available.

E.G.O's standard error codes are listed following, customized UI can be different. In the 

standard general UI eroors (Er xx) and cooking zone errors (E/x) differ. In case of cooking 

zone errors the display of the incorrect cooking zone blinks alternative "E" and a hexco-

de "X".

Error

code

Description

possible

causes

Remedy

.

The cooking zone 

can be configured if 

a static "C" is shown

No error, the user 

is in the service 

menu.

A suitably pan must be 

placed on the relevant 

cooking zone

.

The cooking will be 

configured if a fla-

shing "C" is shown. 

After a successful 

configuration the 

relevant display 

shows "-". If "-" is not 

displayed check the 

possible causes of 

the E/5

User is in the 

service menu, no 

error

Wait for the symbol "-" 

or abort the configu-

ration activities by 

pressing the select key 

and the "C" will not flash 

anymore.

.

A flashing "E" on 

each cooking zone 

indicates that all 

configs will be 

deleted

User is in service 

menu, no error

Manual configuration

.

Temperature limits 

are exceeded

Pt or glass tempe-

rature is too high

NTC -> electronic 

temperature too 

high

System must cool down

.

Unsuitable pot, e.g. 

loss of the magnetic 

characteristics be-

cause of temperatu-

re in the bottom

On the module 

a pot creates 

an improper 

operatioing point 

which can destroy 

devices, e.g IGBTs.

1. The error is automa-

tically cancelled after 8 

s and the cooking zone 

can be used again. In 

case of further upco-

ming errors the pot has 

to be replaced.

2. The module has to 

be changed if the error 

comes without a pot on 

the cooking zone.