Makita VC004GLZ01 - Инструкция по эксплуатации - Страница 22

22 ENGLISH

State of abnormality

Probable cause (malfunction)

Remedy

Cannot erase all tool registrations in 

the cleaner.

Pressing the wireless button on the tool. Press the wireless button on the cleaner for erasing 

all tool registrations.

The stand-by switch on the cleaner is 

not set to "AUTO".

Set the stand-by switch on the cleaner to "AUTO".

The wireless activation button is not 

held down correctly.

Hold down the wireless activation button for more 

than 6 seconds and then release it when the wire-

less activation lamp blinks in red. Hold down the 

wireless activation button for more than 6 seconds 

again until the wireless activation button rapidly 

blinks in red and then release the button.

MAINTENANCE

CAUTION:

Always be sure that the appliance 

is switched off and the battery cartridges are 

removed before attempting to perform inspection 

or maintenance.

NOTICE:

Never use gasoline, benzine, thinner, 

alcohol or the like. Discoloration, deformation or 

cracks may result.

To maintain product SAFETY and RELIABILITY, 

repairs, any other maintenance or adjustment should 

be performed by Makita Authorized or Factory Service 

Centers, always using Makita replacement parts.

Storage of accessories

Accessories and attachments not in use, such as noz

-

zles and brushes, can be hooked and stored in the multi 

hook at the rear of the cleaner.

► 

Fig.40:

1.

 Multi hook 

2.

 Accessories and attach

-

ments not in use

Pipes (with an optional stopper installed) can be placed into 

the pipe holder when not using the cleaner for a short time.

► 

Fig.41:

1.

 Stopper (optional accessory) 

2.

 Pipe holder

A hose can be wrapped and stored around the housing 

or handle of the cleaner in large loops. Connect its both 

ends together to make loops and hook the loops onto 

the handle raised up. Alternatively, keep its root end 

installed in the hose inlet and hang the loops on the 

multi hook with the loose end tied up.

► 

Fig.42

► 

Fig.43

Cleaning of powder filter (HEPA) and 

prefilter

Clean out the powder filter, prefilter and damper at 

regular intervals since clogged filters and damper may 

result in poor suction performance.

Routinely wipe and shake dust off filters and damper 

by hand.

► 

Fig.44:

1.

 Prefilter

► 

Fig.45:

1.

 Damper 

2.

 Powder filter (HEPA)

Occasionally wash the powder filter in water, rinse and 

dry thoroughly in the shade before use. Never wash 

filters in a washing machine.

► 

Fig.46

NOTE:

 Do not rub or scratch the powder filter, the 

prefilter and the damper with hard objects such as a 

brush and a paddle.

NOTE:

 The filters wear out in course of time. It is 

recommended to have some spares for them.

OPTIONAL 

ACCESSORIES

CAUTION:

These accessories or attachments 

are recommended for use with your Makita tool 

specified in this manual.

 The use of any other 

accessories or attachments might present a risk of 

injury to persons. Only use accessory or attachment 

for its stated purpose.

If you need any assistance for more details regard

-

ing these accessories, ask your local Makita Service 

Center.

• 

Hose

• 

Front cuffs (22, 24, 38)

• 

Straight pipe

• 

Extension wand

• 

Corner nozzle

• 

Round brush

• 

Powder filter, HEPA (for dry dust)

• Damper

• 

Prefilter

• 

Nozzle assembly

• 

Bent pipe

• 

Polyethylene bag

• 

Paper pack

• 

MAKPAC adapter

• 

Wireless unit

• 

Makita genuine battery and charger

NOTE:

 Some items in the list may be included in the 

tool package as standard accessories. They may 

differ from country to country.