Ryobi ONE+ LLCDI18022LX - Инструкция по эксплуатации - Страница 8

3

English

OPERATION

NOTE: 

The drill will not run unless the rotation selector is 

pushed fully to the left or right.

Avoid running the drill at low speeds for extended periods 

of  time.  Running  at  low  speeds  under  constant  usage 

may cause the dr

cool the drill by running it without a load and at full speed.

INTERNAL SPINDLE LOCK 

The 

inter

n

al spindle

control of chuck adjustments and bit changes . Squeezing 

the

body stops the chuc

bit changes and chuc

body and turn.

KEYLESS CHUCK

The dr

i

ll  has a k

e

yless 

 chu

ck

 loc

k

 allo

w

s

ill to become

If this occurs , 

 o

v

erheated. 

k adjustments , squeez e the chuc k 

k

from tur

 ja ws 

ning. F

o

r 

 the user single-handed 

chuc k to tighten or release drill 

bits in the chuc

k

 ja ws. The arro ws on the chuc k indicate

which direction to rotate the chuck body in order to 

LOCK

(tighten) or 

UNLOCK

 (release) the drill bit.

WARNING

Do not hold the chuck with one hand and use the 

power of the dr ill to tighten the chuc k jaws on the 

drill bit. The chuc k body could slip in y

or your hand could slip and come in contact with 

the rotating dr ill bit. This could cause an accident 

resulting in serious personal injury.

TWO-SPEED GEAR TRAIN (HI-LO)

The dr ill has a

gear 

tw

o

-speed

designed

dr illing 

 f

o

r 

or

at 

LO (1)

 or 

HI (2

) speeds . A slide s

located on top of the dr

speed. When using drill in the 

LO (1)

 speed range, speed 

will decrease and unit will ha

When using dr

 dr

i

ving 

tr

a

in 

ill to select either

 LO (1)

 or 

HI (2)

ill in the 

HI (2)

 speed range, speed will  

increase and unit will ha

LO (1)

 speed f or high po wer and torque applications and 

HI (2)

 speed for fast drilling or driving applications.

See Figure 6.

ve less

 and torque . Use 

 po

w

er

ve more

and torque . 

 po

w

er 

witch is  

our hand, 

CAUTION:

Never change gears while the tool is r

Failure to obey this caution could result in serious 

damage to the drill.

QUICK MODE SELECTOR

The Quic k Mode Selector allo

w

s y ou to quickly s

w

itch 

from drill mode to drive mode.

In gener

a

l,

mode should be used f

other

duty applications

mode should be  

used for driving screws

 mode should be used 

for impact drilling.

SELECTING DRIVE OR DRILL SETTING

See Figure

Using the char

the type of bit, fastener, and material you will be using.

■

Choose your

 APPLICATION

■

Choose the correct

 SPEED: (1/LOW or 2/HIGH)

■

Choose  the  correct

  MODE:  (DRIVE,  DRILL,  OR 

HAMMER)

. Hammer

 5-6.

. Dr

i

ve 

hea

v

y 

 d

ri

ll 

t belo w, choose correct speed and mode 

or dr illing and  

unning. 

1. APPLICATION

2. SPEED

3. MODE

• Lag screws up to 9.5 mm dia. by 38.1 mm long

• Hole saw up to 50.8 mm

• Spade bits up to 38.1 mm

• Drill bits up to 12.7 mm

• Drilling into metal

• Concrete screws

1/LOW

DRILL MODE

(TORQUE ADJUSMENT NOT ACTIVE) 

2/HIGH

• Drill bits up to 6.4 mm

• Deck or wood screws up to 

76

.

2

 mm long

• Self tapping screws

1/LOW

DRIVE MODE

• Deck or wood screws up to 

76

.

2

 mm long

• Small screws or delicate work that requires more control

2/HIGH

• Masonry bit up to 12.7 mm

1/LOW

HAMMER MODE

(TORQUE ADJUSMENT NOT ACTIVE)

2/HIGH

See Figure 4.

See Figure 5.

EN

FR

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

EL

TR

DE

ES