VITEK VT-1888 - Инструкция по эксплуатации - Страница 10

10

ENGLISH

(fig.  28),  remove  the  cyclone  filter  (39)  (fig.  29)  by 
pulling it upwards using the folding metal handle.

14.4. Remove  the  cyclone  filter  cover  (38)  by  turning  it 

counterclockwise,  then  clean  the  cyclone  filter  (39) 
from dust.

14.5. Clean the dust container canister (40) from dirt.
14.6. Assemble  the  dust  container  and  reinstall  it  in  its 

original place, performing the above steps in reverse 
order (see paragraphs 14.2-14.4).

It  is  recommended  to  clean  the  dust  container  (2)  after 
each use. 
WARNING:  do  not  use  the  unit  without  the  installed  dust 
container complete with filters.

15. GENERAL MAINTENANCE
Make sure the unit is turned off and unplugged. 
Use  only  a  cloth  and  tap  water  to  clean  the  outside  of 
the unit.
All  steam  cleaning  accessories  can  be  cleaned  with 
running  water  and  allowed  to  dry  completely  before 
next use. After using the brushes, allow the bristles to 
cool  in  their  natural  position  to  avoid  deformation.  Do 
not  use  detergents  and  abrasives.  The  fabric  nozzle 
covers can be washed by following the instructions on 
the label.
The  filters  and  canisters  of  the  dust  container  can  be 
cleaned  under  running  water  to  ensure  they  are  com-

pletely  dry  before  next  use.  Rinse  the  canisters  of  the 
cyclone  filter  and  the  dust  container  with  running  wa-
ter and shake to remove excess dirt or water. Allow the 
filters  to  get  completely  dry  naturally  before  installing 
them  into  the  unit,  away  from  heat  sources  for  at  least 
24 hours. The HEPA filter should be completely cleaned 
approximately every four months.

16. STORAGE LOCATION
16.1. Switch the unit off and unplug it. 
16.2. Empty  the  remaining  water  from  the  water  tank  to 

avoid leaks.

16.3. Before removing fabric covers from the nozzles wait a 

few minutes for them to cool down.

16.4. Wind  the  power  cord  around  the  special  winding 

hooks (13, 19) (fig. 30).

Complete the requirements of section 14.
Be  sure  to  completely  unwind  the  power  cord  before  us-
ing the unit again. The upper power cord winding hook (13) 
rotates at 180° to quickly unwind the cord.
WARNING:  do  not  keep  the  unit  connected  to  the  mains 
with the power cord wound.
16.5. The  unit  storage  hook  (33)  can  be  wall-mounted 

using  4  holes  and  the  included  hook  attachment 
kit (34).

The  unit  is  fixed  to  the  storage  hook  (33)  by  the  carrying 
handle (15) (fig. 31).

17. DIAGNOSTICS OF FAULTS

Problem

Cause

Solution

The unit is not switched on. 

No electricity.

Check that the unit is connected to the mains.

No steam comes out. 

The water has run out.

Unplug the unit, fill the water tank and then 
use the unit again.

The device is turned off.

Make sure the unit is connected to a power 
source, the power switch of the handheld 
steam cleaner is in position (I) and the steam 
button (6 or 12) is held down.

The unit is switched on but 
produces little steam.

The steam supply is set to the 
minimum level.

Press the regulation button
Steam dispensing to increase the amount of 
steam dispensed (see section 4).

The unit spills too much 
water onto the floor.

The steam supply is set to the 
maximum level.

Reduce steam supply to the minimum. If 
necessary, temporarily stop dispensing 
steam while continuing to brush the surface.

Steam button is pressed and / 
or held.

Do not keep the steam button (6 or 12) 
constantly pressed, but release it to stabilize 
the temperature.

The suction power drops 
during operation.

The dust container is full. 

Empty the dust container.

Dust comes out of the unit 
during suction.

The dust container is not inserted 
correctly.

Insert the dust container correctly.

The dust container is full.

Empty the dust container.

The dust container cannot 
be removed. 

Filter not inserted correctly

Insert the filter correctly

If problems persist or are not listed above, please contact an authorized service center (www.vitek.ru or contact 
Customer Support.

VT-1888.indd   10

10/20/20   3:24 PM