Franke FMA 97 P XS - Инструкция по эксплуатации - Страница 11

EN

11

CLEANING AND MAINTENANCE

EXTERIOR SURFACES

• Clean the surfaces with a damp microfibre cloth� 

If they are very dirty, add a few drops of pH-neutral 

detergent� Finish off with a dry cloth� 

• Do not use corrosive or abrasive detergents� If any of 

these products inadvertently comes into contact with 

the surfaces of the appliance, clean immediately with 

a damp microfibre cloth�

INTERIOR SURFACES

• After every use, leave the oven to cool and then 

clean it, preferably while it is still warm, to remove 

any deposits or stains caused by food residues� To 

dry any condensation that has formed as a result of 

cooking foods with a high water content, leave the 

oven to cool completely and then wipe it with a cloth 

or sponge� 

• If there is stubborn dirt on the interior surfaces, we 

recommend running the automatic cleaning function 

for optimal cleaning results�

• Clean the glass in the door with a suitable liquid 

detergent� 

• The door can be easily removed and refitted to 

facilitate cleaning of the glass� 

ACCESSORIES

Soak the accessories in a washing-up liquid solution 

after use, handling them with oven gloves if they 

are still hot� Food residues can be removed using a 

washing-up brush or a sponge�

Do not use steam cleaning 

equipment.
Use protective gloves during all 

operations.

Carry out the required 

operations with the oven cold.
Disconnect the appliance from 

the power supply.

Do not use wire wool, abrasive 

scourers or abrasive/corrosive 

cleaning agents, as these could 

damage the surfaces of the 

appliance.

REMOVING AND REFITTING THE DOOR

1.

To remove the door

, open it fully and lower the 

catches until they are in the unlock position�

2.

 Close the door as much as you can� 

Take a firm hold of the door with both hands – do not 

hold it by the handle�

Simply remove the door by continuing to close it 

while pulling it upwards (a) at the same time until it is 

released from its seating (b)�

~60°

a

b

~15°

Put the door to one side, resting it on a soft surface�

3.

Refit the door

 by moving it towards the oven, 

aligning the hooks of the hinges with their seating 

and securing the upper part onto its seating�

4.

 Lower the door and then open it fully�

Lower the catches into their original position: Make 

sure that you lower them down completely� 

5.

 Try closing the door and check to make sure that it 

lines up with the control panel� If it does not, repeat 

the steps above�

PRESS TO CLEAN - CLEANING THE GLASS

1.

 After removing the door and resting it on a soft 

surface with the handle downwards, simultaneously 

press the two retaining clips and remove the upper 

edge of the door by pulling it towards you� 

2.

 Firmly hold the panes of glass with both hands, 

remove them and place them on a soft surface before 

cleaning�

 REPLACING THE LAMP

1.

 Disconnect the oven from the power supply�

2.

� Remove the cover from the light, replace the bulb 

and put the cover back on the light�

3.

 Reconnect the oven to the power supply�

Please note: Only use 25-40W/230V type E-14, T300°C 

incandescent lamps, or 20-40W/230 V type G9, T300°C 

halogen lamps. The bulb used in the product is specifically 

designed for domestic appliances and is not suitable for 

general room lighting within the home (EC Regulation 

244/2009). Light bulbs are available from our After-sales 

Service.

If using halogen bulbs, do not handle them with your bare 

hands as your fingerprints could cause damage. Do not use 

the oven until the light cover has been refitted.