Metabo DS 150 - Инструкция по эксплуатации - Страница 13

ENGLISH

en

13

changed. All persons must stay clear of the danger 

zone when this is performed.

Dry grinding wheel:

- Release the screws on the safety guard cover (1), 

twist and remove the cover (1) (bayonet catch). 

- Hold the grinding wheel (4) firmly in position as 

shown. 

Caution! Risk of injury! Wear 

protective gloves!

- Remove adjusting nut (2) with open-ended 

spanner.

Caution! Left-hand thread on left machine 

side

, i.e. to release the adjusting nut (2)on the left 

machine side, turn clockwise!

- Remove clamping flange (3) and grinding 

wheel (4).

- Secure new grinding wheel (4) in the reverse 

order.

- Remount the safety cover (1). Tighten screws.

- Adjust the spark deflector (10) and workpiece 

support (8) as described in chapter 7.2 and 7.1.

Replacing the wet grinding wheel 

(TNS 175 only):

- Empty the water container (18): hold a collecting 

pan under the container and remove the rubber 

stopper (19). Re-insert the rubber stopper.

- Loosen the 3 screws (17) adequately and lower 

the water container.

- Using one hand, hold the grinding wheel (4) 

secure. 

Caution! Risk of injury! Wear 

protective gloves!

- Remove adjusting nut with open-ended spanner. 

(Loosen by turning anti-clockwise).

- Remove clamping flange and grinding wheel (4).

- Secure new grinding wheel (4) in the reverse 

order.

- Replace the water container  (18).  (17) Tighten 

screws. Fill the water container with the correct 

amount of water (see chapter 7.5)

8.2 Replacing the sanding belt (BS 175 only)

Remove the side sanding belt cover (16): release 

the 2 screws (13), slide the sanding belt cover (16) 

(bayonet catch) and remove.
Swivel out lever (12) as far as it will go. This relieves 

sanding belt tension and it can now be removed 

from the rollers.
Place the new sanding belt on the rollers so that its 

direction of circulation (arrows on the inside of the 

sanding belt) matches the arrow (15)  (16)on the 

side sanding belt cover.  
Return the lever (12) to the original position to 

tension the sanding belt.

Place the side sanding belt cover (16) on the 2 

screws (13) and slide (bayonet catch). Tighten the 

two screws.
Adjust the belt run (see chapter 7.6).
For sanding belts, see Accessories chapter 9..  

8.3 Water container (TNS 175 only)

Regularly replace the water in the water container 

(18). To do this, hold a collecting pan under the 

container and remove the rubber stopper (19).
Dismantle the water container for cleaning 

purposes, as described in chapter 8.1. Use water 

and a brush (no metal bristles) to clean the inside of 

the container.

a

Use only genuine Metabo accessories.
If you need any accessories, check with your 

dealer.
For dealers to select the correct accessory, they 

need to know the exact model designation of your 

power tool.

A Grinding wheels ................. Order No.:

D= 125 mm:

36 P:  ................. 0900025181

60  N:  ................. 0900025190

D= 150 mm:

36 P: ........................ 6.30632

60  N: ........................ 6.30633

D= 175 mm: 

36 P:  ........................ 6.30657

60  N:  ........................ 6.30656

D= 200 mm: 

36 P:  ........................ 6.30784

60  N:  ........................ 6.30785

D= 250 mm: 

36 P:  ........................ 6.30636

60  N:  ........................ 6.30637

Wet grinding wheel

D= 200 mm: ................. 0900025653

B Stand 

Order No.: ............................  6.23867

C Wall bracket 

Order no.: 

....................... 6.23862

DSanding belts

3 x P 40

0900025777

3 x P 60

0900025688

3 x P 80

0900025696

3 x P 100

0900025785

3 x P 120

0900025700

3 x P 180

0900025807

3 x P 240

0900025823

3 x P 400

0900025840

For a complete range of accessories, see 

www.metabo.com or the main catalogue.

Repairs to electrical tools must be carried out by 

qualified electricians ONLY! 

9. Accessories

10. Repairs