Einhell GC-BC 52 I AS - Инструкция по эксплуатации - Страница 26

GB

- 26 -

• 

 Undo the adjusting screw (Fig. 13b/Item D) 

until the carburetor slide is completely open 

when the throttle is fully activated, as shown 

in Figure 13a.

• 

 Retighten the lock nut.

9.6 Setting the idling speed

Important!

 Set the idling speed when the equip-

ment is warm.

Only an authorized service center is allowed to 

set the idling speed. The start-up speed of the 

cutting tool must be at least 1.25 times the idling 

speed.

9.7 Applying grease to the gear unit

After every 20 hours of use add a little gear grea-

se (approx. 10 g) at the lubrication point (C) (Fig. 

7c).

10. Cleaning, storage, transport and 

ordering of spare parts

10.1 Cleaning

• 

Keep the handles free of oil so that you can 

maintain a firm grip.

• 

Clean the equipment as required with a damp 

cloth and, if necessary, mild washing up 

liquid.

Important!

Always pull out the spark boot plug each time 

before carrying out any cleaning. Never immerse 

the equipment in water or other liquids in order to 

clean it.

Store the equipment in a safe and dry place out of 

the reach of children.

10.2 Storage

Important: Never put the equipment into storage 

for longer than 30 days without carrying out the 

following steps.

Storing the equipment

If you intend to store the equipment for longer 

than 30 days, the equipment must be prepared 

accordingly. Otherwise the fuel still remaining in 

the carburetor will evaporate and leave a rubbery 

sediment. This can cause problems when starting 

up the equipment and may require expensive 

repairs.

1.  Slowly remove the fuel tank cap to release 

any pressure that may have formed in the 

tank. Carefully empty the tank.

2.  To remove the fuel from the carburetor, start 

the engine and let it run until it stops.

3.  Leave the engine to cool (approx. 5 minutes).

Note: 

Store the equipment in a dry place and 

far away from possible ignition sources such as 

an oven, a gas-

fi

 red hot water boiler, a gas-

fi

 red 

dryer, etc.

Putting the equipment back into operation

1.  Remove the spark plug (see section 9.4).

2.  Clean the spark plug and check that the 

electrode gap is correct, or insert a new spark 

plug with the correct electrode gap.

3.  Prepare the equipment for operation.

4.  Fill the tank with the relevant mixture of fuel 

and oil. See the section „Fuel and oil“.

10.3 Transport

To transport the machine, empty the petrol tank 

as described in section 10. Clean coarse dirt o

ff

the equipment with a brush or hand brush. Dis-

mantle the drive rod mechanism as described in 

section 5.1.2.

10.4 Ordering spare parts

Please provide the following information on all 

orders for spare parts:

• 

Model/type of the equipment

• 

Article number of the equipment

• 

ID number of the equipment

• 

Part number of the required spare part

For our latest prices and information please go to 

www.isc-gmbh.info

11. Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw 

materials in this packaging can be reused or 

recycled. The equipment and its accessories are 

made of various types of material, such as metal 

and plastic. Defective components must be dispo-

sed of as special waste. Ask your dealer or your 

local council.

Anl_GC_BC_52_I_AS_SPK9.indb   26

Anl_GC_BC_52_I_AS_SPK9.indb   26

09.05.2019   13:17:56

09.05.2019   13:17:56