Einhell GC-BC 52 I AS - Инструкция по эксплуатации - Страница 23

GB

- 23 -

6.  Before starting the equipment

Check the equipment for the following each time 

before use:

• 

 That there are no leaks in the fuel system.

• 

 That the equipment is in perfect condition and 

that the safety devices and cutting devices 

are complete.

• 

 That all screws are securely fastened.

• 

 That all moving parts move smoothly.

6.1 Fuel and oil

Recommended fuels

Use only a mixture of unleaded petrol and special 

2-stroke engine oil. Mix the fuel mixture as indica-

ted on the fuel mixing table.

Important: Do not use a fuel mixture which has 

been stored for longer than 90 days.

Important: Never use 2-stroke oil with a recom-

mended mixing ratio of 100:1. The manufacturer’s 

warranty will be voided in case of engine damage 

due to inadequate lubrication.

Important: Only use containers designed and ap-

proved for the purpose to transport and store fuel.

Pour the correct quantities of petrol and 2-stroke 

oil into the mixing bottle (see scale printed on the 

bottle). Then shake the bottle well.

6.2 Fuel mixture table

Mixing procedure: 40 parts petrol to 1 part oil

Petrol

2-stroke oil

1 liter

25 ml

5 liters

125 ml

7. Operation

 Please note that the statutory regulations gover-

ning noise abatement may di

ff

 er from town to 

town.

Before starting up the equipment remove the pro-

tective caps from the cutting blade.

7.1 Starting the engine when cold

Fill the tank with the required amount of oil/petrol 

mix. See “Fuel and oil”.

1.  Set the equipment down on a hard, level sur-

face.

2.  Press the fuel pump (primer) (Fig. 1/Item 7) 

10 times.

3.  Move the ON/OFF switch (Fig. 1/Item 9) to “I”

4.  Set the choke lever (Fig. 1/Item 5) to „ “.

5.  Hold the equipment 

fi

 rmly and pull out the 

starter cable (Fig. 1/Item 4) until you feel it 

start to resist. Then tug sharply on the starter 

cable 2 times. 

6.  Set the choke lever (Fig. 1/Item 5) to „ “.

7.  Hold the equipment 

fi

 rmly and pull out the 

starter cable (Fig. 1/Item 4) until you feel it 

start to resist. Then tug sharply on the starter 

cable 4 times. The equipment should start.

Important: Never allow the starter cable to 

snap back. This may damage the equipment.

Once the engine has started, allow the equip-

ment to warm up for 10 seconds.

Important: The cutting tool starts to operate 

when the engine is started. 

8.  If the engine does not start up, repeat steps 

4-8 above.

Please note: If the engine does not start up even 

after several attempts, read the section “Engine 

Troubleshooting”. Please note: Always pull the 

starter cord out in a straight line. If it is pulled out 

at an angle, then friction will occur on the eyelet. 

As a result of this friction, the cable will become 

frayed and will wear away faster. Always hold the 

starter handle when the cable retracts. Never 

allow the cable to snap back when it has been 

pulled out.

7.2 Starting the engine when warm

(The equipment has been idle for less than 15-20 

min.)

1.  Set the equipment down on a hard, level sur-

face.

2.  Switch the ON/OFF switch to “I”.

3.  Hold the equipment 

fi

 rmly and pull out the 

starter cable until you feel it start to resist. 

Then tug sharply on the starter cable. The 

equipment should start after 1-2 tugs. If the 

equipment does not start after 6 pulls, repeat 

steps 1 – 7 of the procedure for starting the 

engine from cold.

7.3 Switching o

ff

  the engine

Emergency Stop procedure:

If it becomes necessary to stop the equipment im-

mediately, set the ON/OFF switch to “Stop” or “0”

Normal procedure:

Let go of the throttle lever and wait until the engi-

ne has changed to idling speed. Then set the ON/

OFF switch to “Stop” or “0”.

Anl_GC_BC_52_I_AS_SPK9.indb   23

Anl_GC_BC_52_I_AS_SPK9.indb   23

09.05.2019   13:17:55

09.05.2019   13:17:55