Einhell GC-BC 52 I AS - Инструкция по эксплуатации - Страница 20

GB

- 20 -

Danger!

 When using the equipment, a few safety pre-

cautions must be observed to avoid injuries and 

damage. Please read the complete operating 

instructions and safety regulations with due care. 

Keep this manual in a safe place, so that the in-

formation is available at all times. If you give the 

equipment to any other person, hand over these 

operating instructions and safety regulations as 

well. We cannot accept any liability for damage 

or accidents which arise due to a failure to follow 

these instructions and the safety instructions.

1. Safety regulations

The corresponding safety information can be 

found in the enclosed booklet.

Danger!

Read all safety regulations and instructions.

Any errors made in following the safety regula-

tions and instructions may result in an electric 

shock, 

fi

 re and/or serious injury.

Keep all safety regulations and instructions 

in a safe place for future use.

Safety devices

When working with the equipment, the appropri-

ate plastic guard hood for cutting blade mode or 

cutting line mode must be 

fi

 tted to prevent objects 

being thrown out by the equipment. The integra-

ted blade in the cutting line guard hood automati-

cally cuts the line to the optimum length.

Explanation of the warning signs on the 

equipment (Fig. 14):

1. Warning!

2.  Read the directions for use before operating 

the equipment.

3.  Wear protective headgear, goggles and ear 

mu

ff

 s.

4.  Wear sturdy, non-slip footwear.

5.  Wear safety gloves.

6.  Protect the equipment from rain and damp.

7.  Be careful of objects being thrown out!

8.  Always switch o

ff

  the equipment and pull out 

the spark boot plug before carrying out any 

maintenance work.

9.  All bystanders must be kept at least 15 m 

from the machine.

10.  The equipment continues to rotate!

11.  Caution: Hot equipment parts. Keep your dis-

tance.

12.  Add a little grease (gear grease) after every 

20 hours in operation!

13.  Beware of recoil!

14.  Do not use any saw blades.

2.  Layout and items supplied

2.1 Layout (Fig. 1-13)

1.    Guide pin adapter

2. Guide 

pin

3. Operating 

handle

4. Starter 

cable

5. Choke 

lever

6. Gas 

tank

7.  Fuel pump (primer)

8. Air 

fi

 lter housing cover

9. ON-OFF 

switch

10.  Air 

fi

 lter

11.  Throttle lever

12.  Throttle lock

13.  Line spool with cutting line

14.  Cutting line guard hood

15.  Cutting blade guard hood

16.  Spark plug connector

17.  Harness

18.  Cutting blade

19.  Holder for steady grip

20.  Spark plug connector cover

21.  Handle screw M6

22.  Carrier plate

23.  Pressure plate

24.  Pressure plate cover

25.  Nut M10 (left-hand thread)

26.  Oil/petrol mixing bottle

27.  Spark plug wrench

28.  3x cable tie

29.  Allen key 4 mm

30.  Allen key 5 mm

2.2 Items supplied

Please check that the article is complete as 

speci

fi

 ed in the scope of delivery. If parts are 

missing, please contact our service center or the 

sales outlet where you made your purchase at 

the latest within 5 working days after purchasing 

the product and upon presentation of a valid bill 

of purchase. Also, refer to the warranty table in 

the service information at the end of the operating 

instructions.

• 

 Open the packaging and take out the equip-

ment with care.

• 

 Remove the packaging material and any 

packaging and/or transportation braces (if 

Anl_GC_BC_52_I_AS_SPK9.indb   20

Anl_GC_BC_52_I_AS_SPK9.indb   20

09.05.2019   13:17:55

09.05.2019   13:17:55