Bosch GHG 660 LCD - Инструкция по эксплуатации - Страница 12

12

 | English 

1 609 92A 0LZ | (14.3.14)

Bosch Power Tools

English

Safety Notes

Read all safety warnings and all instructions. 

Failure to follow the warnings and instructions 
may result in electric shock, fire and/or serious 
injury.



Save all safety warnings and all instructions for future 
reference.



This hot air gun is not intended for 

use by children and persons with 
physical, sensory or mental limita-
tions or a lack of experience or 
knowledge. 
This hot air gun can be used by chil-
dren aged 8 or older and by persons 
who have physical, sensory or men-
tal limitations or a lack of experi-
ence or knowledge if a person 
responsible for their safety super-
vises them or has instructed them in 
the safe operation of the hot air gun 
and they understand the associated 
dangers. 

Otherwise, there is a danger 

of operating errors and injuries.



Supervise children. 

This will ensure 

that children do not play with the hot 
air gun.



Children must not be allowed to 

clean and perform maintenance on 
the hot air gun without supervision.



Be careful when working with the power tool. 

The pow-

er tool produces intense heat which can lead to increased 
danger of fire and explosion.



Exercise special care when working close to inflamma-
ble materials. 

The hot air jet or the hot nozzle can ignite 

dust or gases.



Do not operate or work with the power tool in areas 
where there is danger of explosion.



Never direct the hot air jet at the same position for 
longer periods. 

Easily inflammable gases can develop 

e. g., when working plastic, paint, varnish or similar mate-
rials.



Be aware that heat can be conducted to hidden covered 
materials and can ignite them.



After using, place the power tool down in a secure man-
ner and allow it to cool down completely before pack-
ing it away. 

The hot nozzle can cause damage.



Do not leave the switched-on power tool unattended.



Store idle power tools out of the reach of children. Do 
not allow persons unfamiliar with the power tool or 
these instructions to operate the power tool. 

Power 

tools are dangerous in the hands of untrained users.



Do not expose the power tool to rain or wet conditions. 

Water entering a power tool will increase the risk of electric 
shock.



Do not abuse the cord. Never use the cord for carrying, 
pulling or unplugging the power tool. Keep cord away 
from heat, oil, sharp edges or moving parts. 

Damaged or 

entangled cords increase the risk of electric shock.



Always wear safety goggles. 

Safety goggles will reduce 

the risk of injuries.



Disconnect the plug from the socket outlet before mak-
ing any adjustments, changing accessories, or placing 
the power tool aside. 

This safety measure prevents unin-

tentional starting of the power tool.



Check the power tool, cord and plug each time before 
use. Do not use the power tool if damage is determined. 
Do not open the power tool yourself and have it ser-
viced only by a qualified repair person using only origi-
nal spare parts. 

Damaged power tools, cords and plugs in-

crease the risk of electric shock.

Provide for good ventilation of your 
working place. 

Gas and vapour developing 

during working are often harmful to one’s 
health.



Wear safety gloves and do not touch the hot nozzle. 

Danger of burning.



Never direct the hot air jet against persons or animals.



Do not use the power tool as a hairdryer. 

The hot air be-

ing blown out is significantly hotter than that from a hair-
dryer.



When operating the power tool in damp environments 
is unavoidable, use a residual current device (RCD). 

The use of a residual current device (RCD) reduces the risk 
of an electric shock.



Never use the machine with a damaged cable. Do not 
touch the damaged cable and pull the mains plug when 
the cable is damaged while working. 

Damaged cables in-

crease the risk of an electric shock.



Products sold in GB only

: Your product is fitted with a 

BS 1363/A approved electric plug with internal fuse 
(ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should 
be cut off and an appropriate plug fitted in its place by an 
authorised customer service agent. The replacement plug 
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible 
shock hazard and should never be inserted into a mains 
socket elsewhere.

OBJ_BUCH-485-006.book  Page 12  Friday, March 14, 2014  9:12 AM