Bosch PWS 8 125 CE - Инструкция по эксплуатации - Страница 14

English - 2

The machine is intended for cutting, roughing and
brushing metal and stone materials without using
water. For cutting stone, a cutting guide is re-
quired.

For machines with electronic control: With ap-
proved sanding tools, the machine can be used
for sanding and polishing.

Measured values determined according to
EN 50 144.

Typically the A-weighted noise levels of the prod-
uct are: sound pressure level: 88 dB (A); sound
power level: 101 dB (A).
Wear hearing protection!

The typically weighted acceleration is 5.0 m/s

2

.

When using the vibration-dampening auxiliary
handle, the hand-arm vibration at the auxiliary
handle is typically below 2.5 m/s

2

.

 1 On / Off switch

 2 Thumbwheel for speed preselection 

(PWS 8-125 CE / PWS 850 CE /
PWS 9-125 CE)

 3 Auxiliary handle

 4 Spindle lock button

 5 Grinder spindle

 6 Protection guard

 7 Clamping lever

 8 Mounting flange (for the M 14 grinding 

spindle with O-ring)

 9 Grinding / cutting disc *

 10 Clamping nut

 11

quick-clamping nut 

(for M 14 grinder spindle) *

 12 Hand guard *

 13 Rubber sanding pad *

 14 Sanding sheet *

 15 Round nut *

 16 Cup brush *

 17 Cutting guide with dust extraction protection 

guard *

 18 Diamond cutting disc *

 19 Mounting flange M 10

* Not all of the accessories illustrated or described are 

included as standard delivery.

Working safely with this ma-
chine is possible only when the
operating and safety information
are read completely and the in-
structions contained therein are
strictly followed. In addition, the

general safety notes in the enclosed booklet
must be observed. Before using for the first
time, ask for a practical demonstration.

■

Wear protective glasses and hearing protec-
tion.

■

Wear additional protection equipment for your
safety, such as protective gloves, sturdy
shoes, hard hat and apron.

■

The dust that is produced while working can be
detrimental to health, inflammable or explo-
sive. Suitable safety measures are required.
Examples: Some dusts are regarded as carci-
nogenic. Use suitable dust / chip extraction and
wear a dust respirator.

■

Dust from light alloys can burn or explode. Al-
ways keep the workplace clean, as blends of
materials are particularly dangerous.

■

If the mains cable is damaged or cut through
while working, do not touch the cable but im-
mediately pull the mains plug. Never use the
machine with a damaged cable.

■

Connect machines that are used in the open
via a residual current device  (RCD) with an ac-
tuating current of 30 mA maximum. Do not op-
erate the machine in rain or moisture.

■

When working with the machine, always hold it
firmly with both hands and provide for a secure
stance.

■

Secure the workpiece. A workpiece clamped
with clamping devices or in a vice is held more
secure than by hand.

■

Always direct the cable to the rear away from
the machine.

■

Always switch the machine off and wait until it
has come to a standstill before placing it down.

■

For power outage or when the mains plug is
pulled, unlock the On / Off switch immediately
and turn it to the off position. This prevents un-
controlled restarting.

■

The machine must be used only for dry cutting /

grinding.

■

For all work with the machine, the auxiliary
handle 3 must be mounted.

Intended Use

Noise / Vibration Information

Machine Elements

For Your Safety

15 • 1 609 929 F32 • 03.06