Пилы дисковые Ryobi RCS1600-K (5133002779) - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.
Если остались вопросы, задайте их в комментариях после инструкции.
"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
2
| English
LOWER GUARD FUNCTION
Ŷ
Check lower guard for proper closing before each
use. Do not operate the saw if lower guard does not
move freely and close instantly. Never clamp or
tie the lower guard into the open position.
If saw is
accidentally dropped, lower guard may be bent. Raise
the lower guard with the retracting handle and make
sure it moves freely and does not touch the blade or
any other part, in all angles and depths of cut.
Ŷ
Check the operation of the lower guard spring.
If the guard and the spring are not operating
properly, they must be serviced before use.
Lower
guard may operate sluggishly due to damaged parts,
gummy deposits, or a build-up of debris.
Ŷ
Lower guard may be retracted manually only for
special cuts such as “plunge cuts” and “compound
cuts”.
Raise lower guard by retracting handle and as
soon as blade enters the material, the lower guard
must be released.
For all other sawing, the lower guard
should operate automatically.
Ŷ
Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor.
An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
SAFETY INSTRUCTIONS FOR WOOD CUTTING BLADE
Ŷ
Please read the manual and instructions carefully
before using the saw blade and the power tool.
Ŷ
The power tool must be in good condition, the spindle
without deformation and vibration.
Ŷ
Do not use the saw without the guards in position. Keep
guards in good working order and properly maintained.
Ŷ
Ensure the operator is adequately trained in safety
precautions, adjustment, and operation of the power
tool.
Ŷ
Always wear goggles and ear protection when using
the power tool. It is recommended to wear gloves,
sturdy non-slip shoes.
Ŷ
Before using any accessory, consult the instruction
manual. The improper use of an accessory can cause
damage and increase the potential for injury.
Ŷ
Use only blades specified in this manual, complying
with EN 847-1.
Ŷ
Observe the maximum speed marked on the saw
blade. Ensure the speed marked on the saw blade is at
least equal to the speed marked on the saw.
Ŷ
Always use blades with correct size and shape of bore
holes. Blades that do not match the mounting hardware
of the saw will run eccentrically, causing loss of control.
Ŷ
Do not use blades of larger or smaller diameter than
recommended. Do not use any spacers to make the
blade fit onto the spindle.
Ŷ
Check the tips of the saw blade for damage or abnormal
appearance before each use. Tips that are damaged or
loose can become flying objects in use and increase
the chance of personal injury.
Ŷ
Do not use cracked or distorted saw blades. Do not use
saw blades that are damaged or deformed
Ŷ
Scrap the saw blade if damaged, deformed, distorted,
or cracked; repairing is not permitted.
Ŷ
Do not use HSS blades.
Ŷ
Ensure the saw blade is mounted correctly. Tighten
the blade bolt securely before use (tightening torque
approx. 10-15 Nm).
Ŷ
Fastening screw and nuts shall be tightened using the
appropriate spanner.
Ŷ
Extension of the spanner or tightening using hammer
blows is not permitted.
Ŷ
Make sure the blade and flanges are clean and the
recessed sides of the collar are against the blade.
Ŷ
Make sure the blade rotates in the correct direction.
Ŷ
Before use, make a dummy cut without the motor
turned on so the position of the blade, operation of
the guards with respect to other machine parts, and
workpiece may be checked.
Ŷ
Never leave the power tool unattended.
Ŷ
Do not apply lubricants on the blade when it is running.
Ŷ
Never perform any cleaning or maintenance work when
the power tool is still running and the head is not in the
rest position.
Ŷ
Never attempt to stop a power tool in motion rapidly
by jamming a tool or other means against the blade.
Serious accidents can be caused unintentionally in this
way.
Ŷ
Disconnect the saw from the mains supply or battery
before changing blades or carrying out maintenance.
Ŷ
Pay attention to the blade packing and unpacking. It is
easy to be injured by the sharp blade tips.
Ŷ
Use a blade holder or wear gloves when handling a saw
blade.
Ŷ
Keep and store the blade in original packaging or other
suitable packaging. Keep in dry conditions and away
from chemicals which may damage the blade.
WARNING
Ŷ
Wear eye and ear protection.
Ŷ
Wear dust mask.
Ŷ
Do not use any abrasive wheels.
Ŷ
Avoid overheating the blade tips. Do not use dull or
damaged blades. Do not force the tool.
Ŷ
Only use saw blades recommended.
Ŷ
Do not use blades of larger or smaller diameter than
recommended.
Ŷ
Use only blades specified in this manual, complying
with EN 847-1.
LASER SAFETY (RCS1600)
Характеристики
Остались вопросы?Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)
