Kenwood MG700 - Инструкция по эксплуатации - Страница 7

Мясорубки Kenwood MG700 - инструкция пользователя по применению, эксплуатации и установке на русском языке. Мы надеемся, она поможет вам решить возникшие у вас вопросы при эксплуатации техники.

Если остались вопросы, задайте их в комментариях после инструкции.

"Загружаем инструкцию", означает, что нужно подождать пока файл загрузится и можно будет его читать онлайн. Некоторые инструкции очень большие и время их появления зависит от вашей скорости интернета.
Страница:
/ 108
Загружаем инструкцию
background image

to assemble

1 Fit the scroll inside the mincer body.
2 Fit the cutter – cutting side

outermost 

Ensure it’s seated

properly – otherwise you

could damage your mincer.

3 Fit a mincer screen 

. Put the notch

over the pin.

Use the fine screen for raw meat;
fish; small nuts; or cooked meat for
shepherd’s pie or meat loaves.

Use the medium and coarse screens
for raw meat; fish and nuts.

4 Loosely fit the ring nut.

to use the mincer

1 With the mincer attachment in the

position shown 

, locate in the

outlet. Rotate the mincer body so
that the feed tube is upright.

2 Tighten the ring nut firmly by hand.

If you experience poor results when
mincing meat, switch off and unplug
the machine. Dismantle and clean
the attachment, then re-assemble
the attachment and refit to the
power unit. Tighten the ring nut
using the spanner provided 

.

3 Fit the tray. Put the dish/cover under

the mincer to catch the food.

4

Thaw frozen food thoroughly

before mincing.

Cut meat into

2.5cm (1”) -wide strips.

5 Switch to speed 2. Using the pusher,

gently push the food down the feed
tube, one piece at a time. 

Don’t

push hard – you could damage

your mincer.

Note:
Speed 1 is for extruding sausages,
kebbe and for use with the optional
attachments.

To prolong the life of your meat
grinder, never operate the appliance
for longer than 20 minutes, (allow a
rest period of 10 minutes between
batches).

If the machine stalls or overheats
during use, it will stop mincing and
emit a quiet humming noise. In the
case of a stall, switch the machine
off, then turn the control to R (reverse)
for a few seconds to release the
clogged food. Switch off and unplug
the machine and remove any clogged
material. However, if the machine
overheats, switch the machine off and
allow it to cool down for 1 hour
before continuing the mincing
operation.

When selecting reverse, always wait
until the machine stops operating
before turning the speed control to
the reverse (R) position.

6 Switch off and unplug after use.
7 Loosen the ring nut. If necessay use

the spanner provided.

8 Move the locking lever towards the

back of the unit, then rotate the feed
tube towards the front of the
machine, then pull free.

5

4

Полезные видео

Характеристики

Оцените статью
tehnopanorama.ru
Остались вопросы?

Не нашли свой ответ в руководстве или возникли другие проблемы? Задайте свой вопрос в форме ниже с подробным описанием вашей ситуации, чтобы другие люди и специалисты смогли дать на него ответ. Если вы знаете как решить проблему другого человека, пожалуйста, подскажите ему :)

Задать вопрос

Часто задаваемые вопросы
Как посмотреть инструкцию к Kenwood MG700?
Необходимо подождать полной загрузки инструкции в сером окне на данной странице
Руководство на русском языке?
Все наши руководства представлены на русском языке или схематично, поэтому вы без труда сможете разобраться с вашей моделью
Как скопировать текст из PDF?
Чтобы скопировать текст со страницы инструкции воспользуйтесь вкладкой "HTML"