Bosch PFS 5000 E (0603207202) - Инструкция по эксплуатации - Страница 26

26

 | English

– Clean the container 

(7)

.

– Remove the suction tube 

(17)

 with the container

seal 

(16)

 and rinse it thoroughly. 

Reattach the suction tube 

(17)

 with the container

seal 

(16)

 to the spray gun.

– Fill the container 

(7)

 halfway with solvent and fit it to the

spray gun 

(1)

again.

– Shake the spray gun several times.

Make sure that you do not spray the diluting agent. 

There

is a risk of explosion.

– Remove the container 

(7)

 from the spray gun 

(1)

and

empty it completely into a sealable material tin.

– Remove the cap nut 

(3)

, the air cap 

(2)

, the nozzle cap

used 

(10)

/

(11)

/

(12)

 and the suction tube 

(17)

 with the

container seal 

(16)

.

– Clean all paint-carrying parts in a bucket with diluting

agent using the cleaning brush 

(28)

 or with a commer-

cially available washing-up brush. Also clean the paint
channel 

(19)

 of the spray gun 

(1)

.

– Check that the suction tube 

(17)

 and the container

seal 

(16)

 are free of spray material and undamaged.

If required, clean the container seal 

(16)

 again with dilut-

ing agent.

– Clean the ventilation hole 

(18)

 using the cleaning

brush 

(28)

.

– If required, clean the filling sieve 

(13)

 thoroughly with di-

luting agent.

– Clean the outside of the container 

(7)

 and the spray

gun 

(1)

with a cloth moistened in diluting agent.

– Allow all components to dry thoroughly before assem-

bling them.

– Reassemble the fine-spray system in reverse order.

Slide the container seal 

(16)

 upwards again into the

groove of the suction tube 

(17)

.

Ensure that the container seal is positioned precisely all
around in the suction tube groove in order to seal the

spray gun correctly.
Make sure that you slide the suction tube 

(17)

 all the way

back onto the paint channel 

(19)

.

Cleaning the air filter (see figure N)

The air filter 

(30)

 must be cleaned occasionally. The air filter

must be replaced if it is heavily contaminated.
– Open the air filter cover 

(29)

.

– Remove the air filter 

(30)

.

– Light contamination:

Knock on the air filter 

(30)

.

or

Heavy contamination:
Clean the air filter 

(30)

 under running water and sub-

sequently leave it to dry thoroughly, in order to prevent
mould from forming.

or

Replace the air filter 

(30)

.

– Reinsert the air filter.
– Close the air filter cover 

(29)

 again.

u

Never use the fine-spray system without air filter.

 Dirt

particles may get into the motor compartment and dam-
age it.

Material Disposal

Contaminated diluting agent, remnants of spray material
and, if applicable, remnants of diluting agent must be dis-
posed of properly and in an environmentally friendly man-
ner. Observe the manufacturer's disposal information and
the local regulations for disposal of hazardous waste.
Chemicals harmful to the environment may not be disposed
of into soil, groundwater or bodies of water. Never pour
chemicals harmful to the environment into the sewerage sys-
tem.

Storage

– Before putting the fine-spray system into storage, thor-

oughly clean the fine-spray system and allow all parts to
dry completely before assembling them.

Troubleshooting

Problem

Cause

Corrective measure

Spray material does not
cover properly

Spraying capacity too low

Turn the thumbwheel 

(4)

 towards setting 

5

Clearance to target area too large

Reduce spray distance

Not enough spray material on target area, too
few spray paths sprayed over target area

Apply more spray paths over target area

Spray material too viscous

Dilute the spray material again and carry out a
test-spray run

Spray material runs off after
coating

Too much spray material applied

Turn the thumbwheel 

(4)

 towards setting 

1

Clearance to target area too close

Increase spray distance

Viscosity of spray material too low

Add original spray material

Spray material applied too often over same
spot

Remove spray material; reduce number of
spray paths over same spot

Atomisation too coarse

Spraying capacity too high

Turn the thumbwheel 

(4)

 towards setting 

1

Air flow too low

Turn the air flow control 

(25)

 to the right

1 609 92A 686 | (17.06.2021)

Bosch Power Tools