Bosch PFS 5000 E (0603207202) - Инструкция по эксплуатации - Страница 24

24

 | English

– Make sure to hold the spray gun with a uniform clearance

of 20–25 cm vertical to the object being sprayed.

– Begin the spraying procedure outside the target area.
– Move the spray gun evenly horizontally or vertically ac-

cording to the spray pattern configuration.
An even surface quality can be achieved when the spray
paths overlap by 4–5 cm.

– When spraying horizontal objects or spraying overhead,

hold the spray gun at a slight angle and move back from
the sprayed surface.

Risk of tripping! Be aware of potential obstacles.

– Avoid interruptions when spraying the target area.
Guiding the spray gun evenly will provide uniform surface
quality.
A non-uniform spraying angle and distance will lead to heavy
formation of paint mist and consequently an uneven surface.
– End the spraying procedure outside the target area.
Never completely empty the container for the spray material
by spraying. If the suction tube is no longer immersed in the
spray material, the spray jet will be interrupted and this will
result in an inconsistent surface.
– After breaks or refilling the container 

(7)

, check the

nozzle cap 

(10)

/

(11)

/

(12)

 and the air cap 

(2)

 and clean

them if required.

– If spray material settles on the air cap 

(2)

 or the nozzle

cap, clean the components with the supplied cleaning
brush 

(28)

 or a commercially available washing-up brush.

Setting the spray pattern (see figure I)

u

Never actuate the trigger switch (5) while adjusting
the air cap (2).

– Turn the air cap 

(2)

 to the required position.

Air cap

Spray jet pattern Application

Horizontal flat jet
for vertical working
direction

Vertical flat jet for
horizontal working
direction

Round jet for
corners, edges and
hard to reach loca-
tions

Setting the spray material quantity (see figure J)

(

PAINT

Volume)

– Turn the thumbwheel 

(4)

 to set the required spray mater-

ial quantity:
Stages 

1

/

2

/

3

: "Wood/glaze/lacquer" application,

Stages 

4

/

5

: "Wall" application.

– Start with a spray test at setting 

1

 and increase the spray

material volume until the required spray pattern is
achieved. If a satisfactory spray pattern is not achieved,
dilute the spray material in 5 % increments (see "Prepar-
ing the spray material", page 23).

Please note:

 The intensity of the paint application is highly

dependent on the moving speed.

Spray material
volume

Setting

Too much mater-
ial on target area

The spray material volume
must be reduced.

– Turn down by one setting.

Not enough ma-
terial on target
area

The spray material volume
must be increased.

– Turn up by one setting.

Setting the air flow (see figure D)

(

AIR

Volume)

– Turn the air flow control 

(25)

 to select the appropriate

application in order to set the correct air flow and pres-
sure for the spray material used.
Start with minimum/"Wood/glaze" application

Setting the applications

Thin-viscosity spray material Thick-viscosity spray mater-

ial

"Wood/glaze" application

"Wood/lac-

quer" applica-

tion

"Wall" applic-

ation

The air flow and pressure can be steplessly adjusted within
an application.
Excessive paint mist:
The air flow must be reduced.
– Turn the air flow control 

(25)

 to the left.

Atomisation too coarse:
The air flow must be increased.
– Turn the air flow control 

(25)

 to the right.

Dampening Wallpaper

To make it easier to remove old wallpaper, you can spray
warm water on the wallpaper (max. 55 °C). Use the grey
nozzle cap 

(11)

 to do so.

1 609 92A 686 | (17.06.2021)

Bosch Power Tools