Ryobi RGN3600 5133002563 - Инструкция по эксплуатации - Страница 23

9

 English 

|

EN

FR

DE

ES

IT

NL

PT

DA

SV

FI

NO

RU

PL

CS

HU

RO

LV

LT

ET

HR

SL

SK

BG

UK

TR

raised high enough to gain access to the frame bottom. 
Securely position props underneath to support.

■

Position a leg below the holes on the frame crossbar.

■

Insert a two screws through the holes of the leg and 
then the holes in the frame crossbar.

■

Install self-locking nuts and tighten to secure.

■

Repeat for the remaining leg.

OPERATION

 WARNING

Do not allow familiarity with tools to make you careless. 
Remember that a careless fraction of a second is 
suf

fi

 cient to in

fl

 ict serious injury.

 WARNING

Do not use any attachments or accessories not 
recommended by the manufacturer of this product. The 
use of attachments or accessories not recommended 
can result in serious personal injury.

APPLICATIONS

This generator is designed to supply electrical power for 
operating compatible electrical lighting, appliances, tools, 
and motor loads.

BEFORE OPERATING THE PRODUCT

■

Only use outdoors and far away from windows, doors, 
and vents.

■

Never use inside a home or garage, even if the doors 
and windows are open.

■

Always position the generator on a flat firm surface.

■

Check engine lubricant level and fill, if necessary. 
Refer to the "Checking/adding lubricant" section in this 
manual.

■

Check fuel level and fill, if necessary. Refer to the 
"Checking/adding fuel" section in this manual.

 CAUTION

Attempting to start the engine before it has been properly 

fi

 lled with oil will result in equipment failure.

SPECIAL REQUIREMENTS:

Please consult a quali

fi

 ed electrician, electrical inspector, 

or the local agency having jurisdiction:

■

In some areas, generators are required to be registered 
with local utility companies.

■

If the generator is used at a construction site, there may 
be additional regulations which must be observed.

CHECKING/ADDING LUBRICANT

See Figure 4

 CAUTION

Attempting to start the engine before it has been properly 

fi

 lled with oil will result in equipment failure. Engine 

lubricant has a major in

fl

 uence on engine performance 

and service life. For general, all-temperature use, SAE 
10W-30 is recommended. Always use a 4-stroke motor 
lubricant that meets or exceeds the requirements for API 
service classi

fi

 cation SJ.

NOTE:

 Non-detergent or 2-stroke engine lubricants will 

damage the engine and should not be used.

■

Unscrew the oil cap/dipstick and remove.

■

Wipe dipstick clean and re-seat in hole; do not re-
thread.

■

Remove dipstick again and check lubricant level. 
Lubricant level should fall between the minimum and 
maximum marks on the dipstick.

■

If level is low, add engine lubricant until the fluid level 
rises between the minimum and maximum marks on 
the dipstick. 

■

Reinstall the oil cap/dipstick and secure.

CHECKING/ADDING FUEL

See Figure 5

 WARNING

Fuel and its vapors are extremely 

fl

 ammable  and 

explosive. To prevent serious personal injury and 
property damage, handle petrol with care. Keep away 
from ignition sources, handle outdoors only, do not 
smoke while adding fuel, and wipe up spills immediately.

When adding fuel to the generator, make sure the product 
is sitting on a 

fl

 at, level surface. If the engine is hot, let the 

generator cool before adding gas. Always 

fi

 ll the fuel tank 

outdoors with the machine turned off.

■

Remove the fuel cap.

■

Fill the fuel tank to 25 mm below the top of the fuel neck.

■

Replace and secure the fuel cap.

NOTE:

 Always use unleaded gasoline with a pump octane 

rating of 86 or higher. Never use old, stale, or contaminated 
unleaded fuel, and do not use an oil/fuel mixture. Do not 
allow dirt or water into the fuel tank. Do not use E85 fuel.

USING FUEL STABILISER

Fuel gets old, oxidizes, and breaks down over time. Adding 
a fuel stabilizer extends the usable life of fuel and helps 
prevent deposits from forming that can clog the fuel system.
Follow fuel stabilizer manufacturer’s directions for correct 
ratio of stabilizer to fuel.

■

Add stabiliser to fuel tank, then fill with unleaded fuel 
following previous instructions.

NOTE:

 Fuel stabiliser and unleaded fuel can be mixed prior 

to filling the tank by using a gasoline can or other approved 
fuel container and shaking gently to combine.

■

Replace and secure the fuel tank cap.