STIGA MULTICLIP 50 SQ 291501048/ST1 - Инструкция по эксплуатации - Страница 35

EN - 4

5.2.  SAFETY CHECKS

• 

Check the integrity and correct assembly of all machine 

components;

• 

Make sure that all fasteners are tightened correctly;

• 

Keep every surface of the machine clean and dry.

Action

Result

1. 

Start the machine.

2. 

Release  the  engine  /  cutting 

means brake lever.

1. 

The  cutting  means  should 

move.

2. 

The levers must return to the 

neutral position automatically 

and  quickly,  the  engine  must 

switch  off  and  the  cutting 

device must stop within a few 

seconds.

1. 

Start the machine.

2. 

Engage the drive lever.

3. 

Disengage the drive lever.

2.  The machine moves forward.

3.  The  machine  comes  to  a 

standstill.

1. 

Test drive.

1. 

N o   a b n o r m a l   v i b ra t i o n s.

No abnormal sound.

If any of the results fail to match the indications 

provided in the tables, do not use the machine! 

Contact a service centre to have it checked and 

repaired if necessary.

5.3. 

START-UP AND WORK

 NOTE 

  Start the machine on a level surface free from obsta-

cles or grass. 

• 

Models with manual starter hand grip (Fig. 13).

• 

Models with push-button electric starter control (Fig. 14).

 IMPORTANT 

  Always  maintain  a  safe  distance  from  the  cut

-

ting  device  while  working,  corresponding  to  the  length  of  the 

handle.

5.4.  STOP

When you have finished working, release the engine brake 

lever/cutting device (Fig. 15).

When you have stopped the machine, it will take 

a few seconds for the cutting means to stop.

Do not touch the engine after it has been turned 

off. Burn hazard.

5.5.  AFTER OPERATION

• 

Cleaning procedure (Par. 5.1).

• 

If  necessary,  replace  the  damaged  components  and 

tighten any loose screws and bolts.

Whenever you leave the machine unused or unattended:

• 

Remove  the  spark  plug  cap  (for  manual  starter  hand 

grip models).

• 

Press  the  tab  and  remove  the  consent  key  (on  models 

with a push-button electric starter).

6. 

MAINTENANCE

The safety regulations to follow are described in chap. 1. Strictly 

comply with these indications to avoid serious risks or dangers.
Before conducting any inspections, cleaning or maintenance/

adjustment interventions on the machine:

• 

Stop the machine.

• 

Make  sure  that  every  moving  component  has  come  to 

a standstill.

• 

Wait for the engine to cool down.

• 

Remove the spark plug cap.

• 

Remove the safety key or the battery on models with a 

push-button electric starter control).

• 

Use suitable clothing, protective gloves and goggles.

6.1.  CLEANING

Clean thoroughly following the instructions below every time 

it is used.

• 

Wash the machine with water after each cut

• 

Remove grass debris and mud accumulated inside the 

chassis.

• 

Always make sure the air intakes are free of debris.

• 

Do not use aggressive liquids to clean the chassis.

• 

To reduce the risk of fire, keep the engine free of grass 

mulch, leaves or excessive grease.

6.2.  CUTTING MEANS MAINTENANCE

All  work  on  the  cutting  means  (disassembly, 

sharpening, balancing, repairing, reassembly 

and/or replacing) are demanding jobs that require 

special skills as well as special tools. For safety 

reasons,  these  jobs  are  best  carried  out  at  a 

Specialised Centre.

Make sure damaged, misshapen or worn cutting-

means are replaced, together with its own screws 

in place to preserve balance.

 IMPORTANT 

  Always  use  original  cutting  devices  with  the 

code shown in the "Technical Data" table.

6.3.  RECHARGE THE BATTERY

The battery is supplied for electric push-button starter switch 

models. Read the engine instruction manual for instructions 

regarding autonomy, recharging, reinstating and  maintenance 

of the battery.

 NOTE 

  For more information on maintenance, please refer to 

the full instruction manual.