Elica SPACE EDS DIGITAL R BK A/78 - Инструкция по эксплуатации - Страница 17

17 

3.  Speed (power) suction selection key 1: 

press once to 

select the suction speed (power), press again and keep it 
pressed to activate 20 minute (flashing key) functioning 
time, after which the hood turns off (Stand by) 

4.  Speed (power) suction selection key 2: 

press once to 

select the suction speed (power), press again and keep it 
pressed to activate 15 minute (flashing key) functioning 
time, after which the hood turns off (Stand by) 

5.  Speed (power) suction selection key 3: 

press once to 

select the suction speed (power), press again and keep it 
pressed to activate 10 minute (flashing key) functioning 
time, after which the hood turns off (Stand by). 

6.  Intensive suction speed (power) ON/OFF selection 

key (timed): 

press

to select the suction speed (power). 

Functioning time is 5 minutes after which suction turns off 
or returns to the speed (power) previously selected. 

7.

COMFORT button: 

the hood begins to operate in a 

“cyclical” manner when filtering the air, which means the 
motor is activated at speed level 1 for 5 minutes and then 
switched OFF for 30 minutes. This operating mode 
remains set until the OFF button (or any of the speed 
buttons) is pressed; this will stop the COMFORT function 
and activate the motor at the selected speed level.

8.

Reset saturation filters key: 

the hood, through the 

signal of this luminous key, tells the user when it is 
necessary to carry out maintenance of the fat filters and 
the carbon filter. 

Key lit in green: 

carry out

maintenance of the fat filters, 

after which press the key for about 3 seconds and the 
key turns off. 

Key lit in red: 

carry out

maintenance of the carbon filter, 

after which press the key for about 3 seconds and the 
key turns off. 

Attention:

 the hood is preset only for signaling the fat 

filters. 

To enable the signaling of the carbon filter: 

Set the 

hood on OFF, press key 8 for 3 seconds. The key turns 
on in red to signal that the setting has taken place. To 
disenable the carbon filter signal, repeat this operation 
again (the key lights up in green). 

Note:

  A beep sounds each time this key is pressed. 

Maintenance 

ATTENTION! 

Before performing any maintenance operation, 

isolate the hood from the electrical supply by switching off at 
the connector and removing the connector fuse.  
Or if the appliance has been connected through a plug and 
socket, then the plug must be removed from the socket. 

Cleaning 

The cooker hood should be cleaned regularly (at least with the 
same frequency with which you carry out maintenance of the 
fat filters) internally and externally.  Clean using the cloth 
dampened with neutral liquid detergent. Do not use abrasive 
products. 

DO NOT USE ALCOHOL!

WARNING: 

Failure to carry out the basic cleaning 

recommendations of the cooker hood and replacement of the 
filters may cause fire risks.  

Therefore, we recommend observing these instructions. 
The manufacturer declines all responsibility for any damage to 
the motor or any fire damage linked to inappropriate 
maintenance or failure to observe the above safety 
recommendations. 

Grease filter 

Fig. 2 

This must be cleaned once a month (or when the filter 
saturation indication system – if envisaged on the model in 
possession – indicates this necessity)  using non aggressive 
detergents, either by hand or in the dishwasher, which must 
be set to a low temperature and a short cycle. 
When washed in a dishwasher, the grease filter may discolour 
slightly, but this does not affect its filtering capacity. 
Remove the filter holder frame by turning the knobs (

g

) 90° 

that affix the chimney to the cooker hood. 

Charcoal filter (filter version only) 

Fig. 3 
It absorbs unpleasant odours caused by cooking. 

The charcoal filter can be washed once every two months (or 
when the filter saturation indication system – if envisaged on 
the model in possession – indicates this necessity)   using hot 
water and a suitable detergent, or in a dishwasher at 65°C (if 
the dishwasher is used, select the full cycle function and leave 
dishes out). 
Eliminate excess water without damaging the filter, then put it 
in the oven for 10 minutes at 100° C to dry completely. 
Replace the mattress every 3 years and when the cloth is 
damaged. 

Assembly

Place the mat around the grease filter and fix it in place using 
the devices provided. 
Position the upper cap and fix it in place using the fixing pin. 
 
To disassemble, perform the steps in the reverse order. 

Replacing lamps 

Fig. 4 

Disconnect the appliance from the electricity. 

Warning! 

Prior to touching the light bulbs ensure they are 

cooled down. 
Replace the old light bulb with the one of the same type as 
specified in the feature label or near the light lamp on the 
hood. 
• 

Use a small screwdriver as a lever on the borders of the 
lamp in order to remove the lightbulb. 

• 

Slide out the lightbulb to be replaced and replace with a 
new 12V 20W MAX 30° Ø35 12V GU4. 

• 

Carry out the replacement and mount the new lightbulb 
by following instructions in the reverse. 

If the lights do not work, make sure that the lamps are fitted 
properly into their housings before you call for technical 
assistance.