VITEK VT-1255 VT - Инструкция по эксплуатации - Страница 5

have been given supervision or instruction 
concerning use of the appliance by a person 
responsible for their safety

•  Children should be supervised to ensure that 

they do not play with the appliance

BEFORE USAGE

•  Take out the iron from the package and re-

move the protective cartoon covering from 
the iron sole (12).

•  Make sure that the electrical supply voltage 

corresponds to the iron’s operating voltage. 

Note:
The iron’s heating element is broken in 
during the first use; it is normal for a small 
amount of smoke to be released.

CHOICE OF WATER

To fill the water tank use regular tap water. If the 
water is hard then it is recommended to mix it 
with distilled water at a ratio of 1:1, if the water 
is very hard, mix it with distilled water at a ratio 
of 1:2 or use only distilled water. 

Note:
Do not fill the water tank (11) with scented 
liquids, vinegar, starch solutions, descal-
ing reagents, chemical substances etc. 

FILLING THE WATER TANK (pic. 1, 2)

Make sure that the iron is disconnected from 
electrical power before filling it with water. 
Set the steam release regulator (3) to the Off 
position.
•  Open the water tank lid (2).
•  Fill it with water using the water bowl (14). 

Close the lid (2). 

Note:
•  Do not fill it with water above MAX. indi-

cation.

•  If you need to refill the water tank during 

ironing, turn off the iron and unplug the 
power cord from the outlet. 

•  After you finish ironing, open the water 

tank lid (2) and drain the remaining water 
(pic.8).

IRONING TEMPERATURE

Before operating test the heated iron on the old 

cloth to be sure that the iron sole (12) and the 
water tank (11) are clean. 
•  Always check the recommended iron tem-

perature indicated on the tag before ironing. 

•  If the tag does not list the recommended 

ironing temperature, but you know the type 
of fabric, then use the following table to de-
termine the proper temperature.

Signs Fabric type/temperature

•

Synthetics, nylon, acryl, polyester 

(low temperature)

••

Silk/wool (medium temperature)

•••

Cotton/flax (high temperature)

• 

This table is only for smooth materials. 
Fabrics of other types (crimped, raised etc.) 
are best ironed at low temperature. 

•  First sort items by ironing temperature: wool 

with wool, cotton with cotton etc. 

•  The iron heats up faster than is cools down. 

For this reason it is recommended to begin 
ironing at low temperature (for instance syn-
thetic fabrics). After that, move to higher tem-
perature ironing. Cotton and linens should be 
ironed last. 

•  If an item is made from a mix of fabrics, then 

the iron should be set for the fabric with 
the lowest ironing (for instance if an item is 
made from 60% polyester and 40% cotton, it 
should be ironed at the temperature used for 
ironing polyester “

•

”).

•  If you cannot define the fabric the item is 

made from, find a place on it that is hidden 
while wearing and, on practice select the 
ironing temperature (always start at the low-
est and gradually raise it until you get the de-
sired result.)

•  Corduroy and other fabrics that start glossy 

quickly should be ironed strictly in one direc-
tion (along the lines) with slight pressure. 

•  To avoid appearance of glossy spots on the 

synthetic and silk fabrics, iron them back-
side. 

SET TING THE IRONING TEMPERATURE

•  Place the iron on the base (8).
•  Insert the power plug into the outlet.
•  Set the temperature regulator (10) to the re-

quired ironing temperature: “

•

”, “

••

”, “

•••

” 

(depending on the type of fabric), the (9) in-
dicator will light up (Pic.3). 

5

              ENGLISH         

1255.indd   5

1255.indd   5

03.03.2010   15:40:15

03.03.2010   15:40:15