Ryobi RBC52FSBOS 5133002545 - Инструкция по эксплуатации - Страница 36

25

English (Original instructions)

STARTING AND STOPPING

Choke position A

Choke position B

 WARNING

Never start or run the engine inside a closed or poorly 
ventilated area; breathing exhaust fumes can kill.

To start a cold engine by hand:

See 

fi

 gure 15.

1.  Lay the product on the ground.
2.  Push the primer bulb approximately 10 times.
3.  Set the choke lever to position A (choke closed).
4.  Pull the starter grip with a quick 

fi

 rm and consistent 

upward motion until the engine attempts to start. Do 
not pull the starter grip more than 4 times.

5.  Set the choke lever to position B (choke open).
6.  Pull the starter grip until the engine starts. Do not pull 

the starter grip more than 6 times.

NOTE:

 If the engine does not start, repeat the 

procedure from step 3.

7.  Allow engine to warm up for 10 seconds prior to 

operation.

To start a warm engine by hand:

See 

fi

 gure 16.

1.  Lay the product on the ground.
2.  Set the choke lever to position B (choke open).
3.  Pull the starter grip with a quick 

fi

 rm and consistent 

upward motion until the engine starts.

Starting the engine using an electrical starter (optional):

 WARNING

Only use the Ryobi OES18 electrical starter. Use of 
any other starter may damage the engine and cause 
serious personal injury.

 WARNING

Before using the electrical starter to start the product, 
please read and understand completely the operation 
manual of the OES18 electrical starter to avoid 
improper operation and serious personal injury.

To start a cold engine by electrical starter:

See 

fi

 gure 21.

1.  Install the starter bit into the electrical starter with the 

pentagon bit facing outside.

2.  Push the F/R button to the left until the pentagon 

symbol shows on the F/R button.

3.  Lay the product on the ground and make sure that the 

cutting means do not come in contact with anything.

4.  Press the primer bulb 10 times.

NOTE:

 After the 7th press, the fuel should be visible 

in the primer bulb. If not, continue pressing until the 
fuel is visible.

5.  Set the choke lever to position A (choke closed).
6.  Hold the insulated shaft with your left hand and 

use your right hand to put the starter bit shaft to the 
shaft hole on the engine. Make sure the starter bit is 
properly engaged.

NOTE:

 The electrical starter is equipped with a safety 

interlock. Do not press and hold on the switch button 
when putting the electrical starter shaft into the shaft 
hole on the engine. The starter will not turn if the 
electrical starter is not properly engaged.

7.  Press and hold the electrical starter switch button until 

the engine attempts to start. Do not press the electrical 
starter for more than 4 seconds.

8.  Set the choke lever to position B (choke open).
9.  Press and hold the electrical starter switch button until 

the engine starts.

NOTE:

 If the engine does not start, repeat the 

procedure from step 5. Do not repeat the procedure 
more than 1 time. If the engine does not start after 
the second attempt, see the solution instruction for the 
"Flooded engine" in the "Troubleshooting" section of 
this manual.

10. Allow the engine to warm up for 10 seconds prior to 

operation.

To start a warm engine by electrical starter:

See 

fi

 gure 22.

1.  Install the starter bit into the electrical starter with the 

pentagon bit facing outside.

2.  Push the F/R button to the left until the pentagon 

symbol shows on the F/R button.

3.  Lay the product on the ground and make sure that the 

cutting means do not come in contact with anything.

4.  Set the choke lever to position B (choke open).
5.  Hold the insulated shaft with your left hand and 

use your right hand to put the starter bit shaft to the 
shaft hole on the engine. Make sure the starter bit is 
properly engaged.

6.  Press and hold the electrical starter switch button until