Ryobi RBC52FSBOS 5133002545 - Инструкция по эксплуатации - Страница 29

18

English (Original instructions)

■

Exercise extreme caution when using the blade with 
the product. Blade thrust is the reaction that may occur 
when the spinning blade contacts anything it cannot 
cut. This contact may cause the blade to stop for an 
instant, and suddenly “thrust” the product away from 
the object that was hit. This reaction can be violent 
enough to cause the operator to lose control of the 
product. Blade thrust may occur without warning if 
the blade snags, stalls, or binds. This is more likely to 
occur in areas where it is difficult to see the material 
being cut. 

■

For cutting ease and safety, approach the weeds 
being cut from the right to the left. In the event when an 
unexpected object or woody stock is encountered, this 
practice could minimize the blade thrust reaction. Both 
hands must be used at all times to control the product.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still 
impossible to completely eliminate certain residual risk 
factors. The following hazards may arise in use and 
the operator should pay special attention to avoid the 
following:

■

Injury caused by contact with cutting means. Ensure 
that the blade protectors are fitted when the product is 
not in use. Keep hands and feet away from the blades 
at all times.

■

Injury caused by vibration. Always use the right tool for 
the job, use designated handles and restrict working 
time and exposure.

■

Hearing injury caused by exposure to noise. Wear 
hearing protection and limit exposure.

■

Eye injury due to flying debris. Wear eye protection 
at all times.

■

Injury caused by kickback can occur when using the 
brushcutter. Ensure proper control by using both 
hands on the designated handles. Read and follow 
the directions in this manual to help reduce the risk 
of kickback.

■

Injury caused by falling objects. Wear head protection 
if there is any risk of falling objects.

RISK REDUCTION

It has been reported that vibrations from handheld tools 
may contribute to a condition called Raynaud’s Syndrome 
in certain individuals. Symptoms may include tingling, 
numbness, and blanching of the 

fi

 ngers, usually apparent 

upon exposure to cold. Hereditary factors, exposure to cold 
and dampness, diet, smoking, and work practices are all 
thought to contribute to the development of these symptoms. 

It is presently unknown what, if any, vibrations or extent 
of exposure may contribute to the condition. There are 
measures that can be taken by the operator to possibly 
reduce the effects of vibration:

a)  Keep your body warm in cold weather. When 

operating the product, wear gloves to keep 
the hands and wrists warm. It is reported that 
cold weather is a major factor contributing to 
Raynaud's Syndrome.

b)  

After each period of operation, exercise to 
increase blood circulation.

c)  Ensure that the product is correctly located in a 

designated working position before starting. 

d)  Limit the amount of exposure per day. Take 

frequent work breaks.

e)  If you experience any of the symptoms of this 

condition, immediately discontinue use and see 
your doctor.

 WARNING

Injuries may be caused or aggravated by prolonged 
use of the product. When using any tool for prolonged 
periods, ensure you take regular breaks.

TRANSPORTATION AND STORAGE

■

Stop the engine and allow it to cool before storing or 
transporting.

■

Clean all foreign material from the product.

■

If a cutting blade is fitted, cover it with the blade 
protector.

■

Drain all fuel from tank into a container approved for 
petrol. Remember to properly replace and tighten the 
fuel cap.

■

Run the engine until it stops. This will remove all fuel 
that could become stale and leave varnish and gum in 
the fuel system.

■

Store the product in a cool, dry, and well-ventilated 
place that is inaccessible to children. Keep away from 
corrosive agents such as garden chemicals and de-
icing salts. 

■

Do not store outdoors.

■

When transporting the product in a vehicle, secure 
it against movement or falling to prevent injury to 
persons or damage to the product.

■

Never carry or transport the product while the engine 
is running.

■

Abide by all government and local regulations for the 
safety storage and handling of petrol.