Ryobi RBC52FSBOS 5133002545 - Инструкция по эксплуатации - Страница 28

17

English (Original instructions)

■

Always stop the engine, allow it to cool, and make sure 
all moving parts have come to a complete stop before:

●

servicing

●

leaving the product unattended

●

cleaning your product

●

changing accessories

●

clearing blockages

●

checking for any damage after hitting an object

●

checking for any damage if the product starts to 
vibrate abnormally

●

performing maintenance

●

removing the blade

●

installing the blade

 WARNING

Never use cutting means or attachments which are not 
speci

fi

 ed by Ryobi in this manual. This includes the use 

of metal multi-piece pivoting chains and 

fl

 ail-blades. 

These items are known to break up during use and 
present a high risk of serious injury to the operator or 
bystanders.

 WARNING

Inspection after dropping or other impacts: Thoroughly 
inspect the product and identify any problems or 
damage to it. Any part that is damaged should be 
properly repaired or replaced by an authorised service 
centre.

TRIMMER SAFETY WARNINGS

■

Replace string head if cracked, chipped, or damaged 
in any way. Be sure the string head or blade is properly 
installed and securely fastened. Failure to do so can 
cause serious injury.

■

Avoid using on wet grass.

■

Do not walk backwards when using the product.

■

Walk, never run.

■

The small blade fitted to the cutting attachment guard 
is designed to trim the new extended line to the correct 
length, for a safe and optimum performance. It is very 
sharp; do not touch it, particularly when cleaning the 
product.

■

Always ensure that ventilation openings are kept clear 
of debris.

■

Before each use and after any impact, check that there 
are no damaged parts. Examine the cutting means 
for signs of cracking or other damage. A defective 

switch or any part that is damaged should be properly 
repaired or replace by an authorised service facility.

■

Make sure the head attachment is properly installed 
and securely fastened.

■

Make sure all guards, deflectors, and handles are 
properly and securely attached.

■

Do not modify the product in any way, this may 
increase the risk of injury to yourself or others.

■

Use only the manufacturer's replacement line in the 
cutting head. Do not use any other cutting attachment.

■

Never operate the product without the cutting 
attachment guard in place and in good condition.

■

Maintain a firm grip on both handles while trimming. 
Keep the string head below waist level. Never cut with 
the string head located over 76 cm above the ground.

BRUSHCUTTER SAFETY WARNINGS

■

In addition to the above rules, these additional 
instructions are appropriate when using the product in 
brushcutter mode.

■

Use heavy-duty gloves while installing or removing 
blades. They have sharp edges.

■

Do not attempt to touch or stop the blade when it is 
rotating.

■

A moving blade can cause severe injury. Maintain 
proper control of the product with both hands until the 
blade has completely stopped rotating.

■

Replace any blade that has been damaged. Always 
make sure the blade is installed correctly and securely 
fastened before each use.

■

Use only the manufacturer’s replacement Tri-Arc™ or 
saw blade. Do not use any other cutting attachment. 

■

Never cut any material over 13 mm diameter for Tri-
Arc™ blade and over 40 mm diameter for the saw 
blade.

■

Your brushcutter is fitted with a harness. Carefully 
adjust the harness to fit comfortably. The harness 
supports the weight of the product at your right side.

■

Identify the quick-release mechanism and practice 
using it before you start using the product. Its correct 
use may prevent serious injury in the case of an 
emergency. Never wear additional clothing over the 
harness or otherwise restrict access to the quick-
release mechanism. 

■

Cover the blade with the blade protector before storing 
the product or during transportation. Always remove 
the blade protector before using the product. If not 
removed, the blade protector could become a thrown 
object when the blade begins to turn.