Ryobi RBC47SEO 5133002542 - Инструкция по эксплуатации - Страница 24

15

English (Original instructions)

●

cleaning your product

●

changing accessories

●

clearing blockages

●

checking for any damage after hitting an object

●

checking for any damage if the product starts to 
vibrate abnormally

●

performing maintenance

●

removing blade

●

installing blade

 WARNING

Never use cutting means or attachments, which are 
not specified by Ryobi in this manual. This includes 
the use of metal multi-piece pivoting chains and flail-
blades. These items are known to break up during use 
and present a high risk of serious injury to the operator 
or bystanders.

 WARNING

Inspection after dropping or other impacts: Thoroughly 
inspect the product and identify any problems or 
damage to it. Any part that is damaged should be 
properly repaired or replaced by an authorised service 
centre.

GRASS TRIMMER SAFETY WARNINGS

■

Replace the string head if cracked, chipped, or 
damaged in any way. Be sure the string head is 
properly installed and securely fastened. Failure to do 
so can cause serious injury.

■

Avoid using on wet grass.

■

Do not walk backwards when using the product.

■

Walk, never run.

■

The small blade fitted to the cutting attachment guard 
is designed to trim the new extended line to the correct 
length for safe and optimum performance. It is very 
sharp; do not touch it, particularly when cleaning the 
product.

■

Always ensure that ventilation openings are kept clear 
of debris.

■

Before use and after any impact, check that there 
are no damaged parts. Examine the cutting means 
for signs of cracking or other damage. A defective 
switch or any part that is damaged should be properly 
repaired or replaced by an authorised

service facility.

■

Make sure the head attachment is properly installed 
and securely fastened.

■

Make sure all guards, deflectors, handles, bolts, and 
fasteners are properly and securely attached.

■

Do not modify the product in any way. This may 
increase the risk of injury to yourself or others.

■

Use only the manufacturer’s replacement line in the 
cutting head. Do not use any other cutting attachment.

■

Never use the product without the cutting attachment 
guard in place and in good condition.

■

Maintain a firm grip on both handles while trimming. 
Keep string head below waist level. Never cut with 
the string head located over 76 cm or more above the 
ground.

BRUSHCUTTER SAFETY WARNINGS

■

In addition to the above rules, these additional 
instructions are appropriate when using the product in 
brushcutter mode.

■

Use heavy-duty gloves while installing or removing the 
blades, they have sharp edges.

■

Do not attempt to touch or stop the blade when it is 
rotating.

■

A moving blade can cause severe injury. Maintain 
proper control of the product with both hands until the 
blade has completely stopped rotating.

■

Replace any blade that has been damaged. Always 
make sure the blade is installed correctly and securely 
fastened before each use.

■

Use only the manufacturer’s replacement Tri-Arc™ 
blade. Do not use any other cutting attachment.

■

Never cut any material over 13 mm diameter.

■

Your brushcutter is fitted with a harness. Carefully 
adjust the harness to fit comfortably and help to 
support the weight of the product at your right side.

■

Identify the quick release mechanism and practice 
using it before you start using the product. Its 
correct use may prevent serious injury in case of 
an emergency. Never wear additional clothing over 
the harness or otherwise restrict access to the quick 
release mechanism.

■

Cover the blade with the blade protector before storing 
the product, or during transportation. Always remove 
the blade protector before using the product. If not 
removed, the blade protector could become a thrown 
object as the blade begins to turn.

■

Exercise extreme caution when using the blade with 
the product. Blade thrust is the reaction that may occur 
when the spinning blade contacts anything it cannot 
cut. This contact may cause the blade to stop for an 
instant, and suddenly “thrust” the product away from 
the object that was hit. This reaction can be violent 
enough to cause the operator to lose control of the 
product. Blade thrust may occur without warning if 
the blade snags, stalls, or binds. This is more likely to 

English (Original Instruction)