Makita DUR190LZX3 - Инструкция по эксплуатации - Страница 19

19 ENGLISH

Indicating the remaining battery capacity

Only for battery cartridges with the indicator

► 

Fig.6:

1.

 Indicator lamps 

2.

 Check button

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps 

light up for a few seconds.

Indicator lamps

Remaining 

capacity

Lighted

Off

Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the 

battery.

The battery 

may have

malfunctioned.

NOTE:

 Depending on the conditions of use and the 

ambient temperature, the indication may differ slightly 

from the actual capacity.

Main power switch

Tap the main power button to turn on the tool.

To turn off the tool, press and hold the main power 

button until the speed indicator goes off.

► 

Fig.7:

1.

 Speed indicator 

2.

 Main power button

NOTE:

 The tool will automatically turned off if it is left 

without any operations for a certain period of time.

Switch action

WARNING:

Before installing the battery car-

tridge on the tool, always check to see that the 

switch trigger actuates properly and returns to 

the "OFF" position when released. 

Operating a tool 

with a switch that does not actuate properly can lead 

to loss of control and serious personal injury.

CAUTION:

Never put your finger on the switch when 

carrying.

 The tool may start unintentionally and cause injury.

To prevent the switch trigger from being accidentally 

pulled, a lock-off lever is provided.

To start the tool, grasp the handle (the lock-off lever is 

released by the grasp) and then pull the switch trigger. 

To stop the tool, release the switch trigger.

DUR190U and DUR191U

► 

Fig.8:

1.

 Lock-off lever 

2.

 Switch trigger

DUR190L and DUR191L

► 

Fig.9:

1.

 Lock-off lever 

2.

 Switch trigger

NOTE:

 The tool is automatically turned off after the 

tool is left for a certain period without any operations.

Speed adjusting

You can select the tool speed by tapping the main 

power button. Each time you tap the main power button, 

the level of speed will change.

► 

Fig.10:

1.

 Speed indicator 

2.

 Main power button 

3.

 ADT indicator

Speed indicator

Mode

Rotation speed

ADT

3,500 - 6,000  min

-1

High

6,000 min

-1

Medium

5,100 min

-1

Low

3,500 min

-1

NOTE:

 When you set ADT (Automatic Torque Drive 

Technology), ADT indicator turns on and the tool runs 

at optimum rotation speed and torque for the condi-

tion of grass being cut.

Reverse button for debris removal

WARNING:

Switch off the tool and remove 

the battery cartridge before you remove entan-

gled weeds or debris which the reverse rotation 

function can not remove.

 Failure to switch off and 

remove the battery cartridge may result in serious 

personal injury from accidental start-up.

This tool has a reverse button to change the direction of 

rotation. It is only for removing weeds and debris entan-

gled in the tool.

To reverse the rotation, tap the reverse button and pull 

the switch trigger while depressing the lock-off lever when 

the cutting tool is stopped. The speed indicators and 

ADT indicator start blinking, and the cutting tool rotates in 

reverse direction when you pull the switch trigger.

To return to regular rotation, release the trigger and wait 

until the cutting tool stops.

► 

Fig.11:

1.

 Speed indicator 

2.

 ADT indicator 

3.

 Reverse button

NOTE:

 During the reverse rotation, the tool operates 

only for a short period of time and then automatically 

stops.

NOTE:

 Once the tool is stopped, the rotation returns 

to regular direction when you start the tool again.

NOTE:

 If you tap the reverse button while the cutting 

tool is still rotating, the tool comes to stop and to be 

ready for reverse rotation.