Makita DUR190LZX3 - Инструкция по эксплуатации - Страница 18

18 ENGLISH

PARTS DESCRIPTION

► 

Fig.4

1

Speed indicator

2

ADT indicator 

(ADT = Automatic Torque 

Drive Technology)

3

Caution lamp

4

Main power button

5

Reverse button

6

Battery cartridge

7

Lock-off lever

8

Switch trigger

9

Hanger

10

Handle

11

Barrier (country specific)

12

Protector

13

Lock lever 

(DUR191U and 

DUR191L only)

14

Joint cover 

(DUR191U and 

DUR191L only)

15

Cap 

(DUR191U and 

DUR191L only)

16

Shoulder harness

FUNCTIONAL 

DESCRIPTION

WARNING:

Always be sure that the tool is 

switched off and the battery cartridge is removed 

before adjusting or checking function on the tool.

Failure to switch off and remove the battery cartridge 

may result in serious personal injury from accidental 

start-up.

Installing or removing battery 

cartridge

CAUTION:

Always switch off the tool before 

installing or removing of the battery cartridge.

CAUTION:

Hold the tool and the battery car-

tridge firmly when installing or removing battery 

cartridge.

 Failure to hold the tool and the battery 

cartridge firmly may cause them to slip off your hands 

and result in damage to the tool and battery cartridge 

and a personal injury.

► 

Fig.5:

1.

 Red indicator 

2.

 Button 

3.

 Battery cartridge

To remove the battery cartridge, slide it from the tool 

while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the 

battery cartridge with the groove in the housing and slip 

it into place. Insert it all the way until it locks in place 

with a little click. If you can see the red indicator on the 

upper side of the button, it is not locked completely.

CAUTION:

Always install the battery cartridge 

fully until the red indicator cannot be seen.

 If not, 

it may accidentally fall out of the tool, causing injury to 

you or someone around you.

CAUTION:

Do not install the battery cartridge 

forcibly.

 If the cartridge does not slide in easily, it is 

not being inserted correctly.

Tool / battery protection system

The tool is equipped with a tool/battery protection 

system. This system automatically cuts off power to 

the motor to extend tool and battery life. The tool will 

automatically stop during operation if the tool is placed 

under one of the following conditions:

Caution lamp

Status

Color

 On

 Blinking

Red

Overload

Red

Overheat

Red

Over 

discharge

Overload protection

If the tool gets into one of the following situation, the tool auto-

matically stops and the caution lamp starts blinking in red:
—  The tool is overloaded by entangled weeds or 

other debris.

—  The cutting tool is locked or kicked back.
—  The main power button is turned on while the 

switch trigger is being pulled.

In this situation, release the switch trigger and remove 

entangled weeds or debris if necessary. After that, pull 

the switch trigger again to resume.

CAUTION:

If you need to remove the entan-

gled weeds on the tool or release the locked 

cutting tool, be sure to turn the tool off before you 

start.

Overheat protection for tool or battery

If the tool or battery cartridge is overheated, the tool 

stops automatically. When the tool or battery cartridge is 

overheated, the speed indicator and ADT indicator go off 

and the caution lamp lights up in red. Let the tool and/or 

battery cool down before turning the tool on again.

Overdischarge protection

When the battery capacity becomes low, the tool stops 

automatically. The speed indicator and ADT indicator go 

off and the caution lamp starts blinking in red.

If the tool does not operate even when the switches are 

operated, remove the battery cartridge from the tool and 

charge it.